| Age | Commit message (Collapse) | Author |
|---|
|
1) Old code was hard to maintain, due to complex lock chains.
(We probably will be able to remove some kfree_rcu() in callers)
2) Using a single timer to update all estimators does not scale.
3) Code was buggy on 32bit kernel (WRITE_ONCE() on 64bit quantity
is not supposed to work well)
In this rewrite :
- I removed the RB tree that had to be scanned in
gen_estimator_active(). qdisc dumps should be much faster.
- Each estimator has its own timer.
- Estimations are maintained in net_rate_estimator structure,
instead of dirtying the qdisc. Minor, but part of the simplification.
- Reading the estimator uses RCU and a seqcount to provide proper
support for 32bit kernels.
- We reduce memory need when estimators are not used, since
we store a pointer, instead of the bytes/packets counters.
- xt_rateest_mt() no longer has to grab a spinlock.
(In the future, xt_rateest_tg() could be switched to per cpu counters)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check if the returned device from tcf_exts_get_dev function supports tc
offload and in case the rule can't be offloaded, set the filter hw_dev
parameter to the original device given by the user.
The filter hw_device parameter should always be set by fl_hw_replace_filter
function, since this pointer is used by dump stats and destroy
filter for each flower rule (offloaded or not).
Fixes: 7091d8c7055d ('net/sched: cls_flower: Add offload support using egress Hardware device')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Made kernel accept IPv6 routes with IPv4-mapped address as next-hop.
It is possible to configure IP interfaces with IPv4-mapped addresses, and
one can add IPv6 routes for IPv4-mapped destinations/prefixes, yet prior
to this fix the kernel returned an EINVAL when attempting to add an IPv6
route with an IPv4-mapped address as a nexthop/gateway.
RFC 4798 (a proposed standard RFC) uses IPv4-mapped addresses as nexthops,
thus in order to support that type of address configuration the kernel
needs to allow IPv4-mapped addresses as nexthops.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check of the return value of sock_register() is ineffective.
"if(!err)" seems to be a typo. It is better to propagate the error code
to the callers of caif_sktinit_module(). This patch removes the check
statment and directly returns the result of sock_register().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188751
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
copy_from_iter_full(), copy_from_iter_full_nocache() and
csum_and_copy_from_iter_full() - counterparts of copy_from_iter()
et.al., advancing iterator only in case of successful full copy
and returning whether it had been successful or not.
Convert some obvious users. *NOTE* - do not blindly assume that
something is a good candidate for those unless you are sure that
not advancing iov_iter in failure case is the right thing in
this case. Anything that does short read/short write kind of
stuff (or is in a loop, etc.) is unlikely to be a good one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-03
Here's a set of Bluetooth & 802.15.4 patches for net-next (i.e. 4.10
kernel):
- Fix for a potential NULL deref in the ieee802154 netlink code
- Fix for the ED values of the at86rf2xx driver
- Documentation updates to ieee802154
- Cleanups to u8 vs __u8 usage
- Timer API usage cleanups in HCI drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to commit c0371da6047a ("put iov_iter into msghdr") in v3.19, there
was no check that the iovec contained enough bytes for an ICMP header,
and the read loop would walk across neighboring stack contents. Since the
iov_iter conversion, bad arguments are noticed, but the returned error is
EFAULT. Returning EINVAL is a clearer error and also solves the problem
prior to v3.19.
This was found using trinity with KASAN on v3.18:
BUG: KASAN: stack-out-of-bounds in memcpy_fromiovec+0x60/0x114 at addr ffffffc071077da0
Read of size 8 by task trinity-c2/9623
page:ffffffbe034b9a08 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: kasan: bad access detected
CPU: 0 PID: 9623 Comm: trinity-c2 Tainted: G BU 3.18.0-dirty #15
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc000209c98>] dump_backtrace+0x0/0x1ac arch/arm64/kernel/traps.c:90
[<ffffffc000209e54>] show_stack+0x10/0x1c arch/arm64/kernel/traps.c:171
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc000f18dc4>] dump_stack+0x7c/0xd0 lib/dump_stack.c:50
[< inline >] print_address_description mm/kasan/report.c:147
[< inline >] kasan_report_error mm/kasan/report.c:236
[<ffffffc000373dcc>] kasan_report+0x380/0x4b8 mm/kasan/report.c:259
[< inline >] check_memory_region mm/kasan/kasan.c:264
[<ffffffc00037352c>] __asan_load8+0x20/0x70 mm/kasan/kasan.c:507
[<ffffffc0005b9624>] memcpy_fromiovec+0x5c/0x114 lib/iovec.c:15
[< inline >] memcpy_from_msg include/linux/skbuff.h:2667
[<ffffffc000ddeba0>] ping_common_sendmsg+0x50/0x108 net/ipv4/ping.c:674
[<ffffffc000dded30>] ping_v4_sendmsg+0xd8/0x698 net/ipv4/ping.c:714
[<ffffffc000dc91dc>] inet_sendmsg+0xe0/0x12c net/ipv4/af_inet.c:749
[< inline >] __sock_sendmsg_nosec net/socket.c:624
[< inline >] __sock_sendmsg net/socket.c:632
[<ffffffc000cab61c>] sock_sendmsg+0x124/0x164 net/socket.c:643
[< inline >] SYSC_sendto net/socket.c:1797
[<ffffffc000cad270>] SyS_sendto+0x178/0x1d8 net/socket.c:1761
CVE-2016-8399
Reported-by: Qidan He <i@flanker017.me>
Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tsq_flags being in the same cache line than sk_wmem_alloc
makes a lot of sense. Both fields are changed from tcp_wfree()
and more generally by various TSQ related functions.
Prior patch made room in struct sock and added sk_tsq_flags,
this patch deletes tsq_flags from struct tcp_sock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a likely() in tcp_mtu_probe() moves its code which used to
be inlined in front of tcp_write_xmit()
We still have a cache line miss to access icsk->icsk_mtup.enabled,
we will probably have to reorganize fields to help data locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Always allow the two first skbs in write queue to be sent,
regardless of sk_wmem_alloc/sk_pacing_rate values.
This helps a lot in situations where TX completions are delayed either
because of driver latencies or softirq latencies.
Test is done with no cache line misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under high load, tcp_wfree() has an atomic operation trying
to schedule a tasklet over and over.
We can schedule it only if our per cpu list was empty.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under high stress, I've seen tcp_tasklet_func() consuming
~700 usec, handling ~150 tcp sockets.
By setting TCP_TSQ_DEFERRED in tcp_wfree(), we give a chance
for other cpus/threads entering tcp_write_xmit() to grab it,
allowing tcp_tasklet_func() to skip sockets that already did
an xmit cycle.
In the future, we might give to ACK processing an increased
budget to reduce even more tcp_tasklet_func() amount of work.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of atomically clear TSQ_THROTTLED and atomically set TSQ_QUEUED
bits, use one cmpxchg() to perform a single locked operation.
Since the following patch will also set TCP_TSQ_DEFERRED here,
this cmpxchg() will make this addition free.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a cleanup, to ease code review of following patches.
Old 'enum tsq_flags' is renamed, and a new enumeration is added
with the flags used in cmpxchg() operations as opposed to
single bit operations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function br_sysfs_addbr() does not set error code when the call
kobject_create_and_add() returns a NULL pointer. It may be better to
return "-ENOMEM" when kobject_create_and_add() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188781
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding space after switch keyword before open
parenthesis for readability purpose.
This patch fixes the checkpatch.pl warning:
space required before the open parenthesis '('
Signed-off-by: Suraj Deshmukh <surajssd009005@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been reported that update_suffix can be expensive when it is called
on a large node in which most of the suffix lengths are the same. The time
required to add 200K entries had increased from around 3 seconds to almost
49 seconds.
In order to address this we need to move the code for updating the suffix
out of resize and instead just have it handled in the cases where we are
pushing a node that increases the suffix length, or will decrease the
suffix length.
Fixes: 5405afd1a306 ("fib_trie: Add tracking value for suffix length")
Reported-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It wasn't necessary to pass a leaf in when doing the suffix updates so just
drop it. Instead just pass the suffix and work with that.
Since we dropped the leaf there is no need to include that in the name so
the names are updated to node_push_suffix and node_pull_suffix.
Finally I noticed that the logic for pulling the suffix length back
actually had some issues. Specifically it would stop prematurely if there
was a longer suffix, but it was not as long as the original suffix. I
updated the code to address that in node_pull_suffix.
Fixes: 5405afd1a306 ("fib_trie: Add tracking value for suffix length")
Suggested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch (default on) can be used to disable automatic registration
of connection tracking functionality in newly created network
namespaces.
This means that when net namespace goes down (or the tracker protocol
module is unloaded) we *might* have to unregister the hooks.
We can either add another per-netns variable that tells if
the hooks got registered by default, or, alternatively, just call
the protocol _put() function and have the callee deal with a possible
'extra' put() operation that doesn't pair with a get() one.
This uses the latter approach, i.e. a put() without a get has no effect.
Conntrack is still enabled automatically regardless of the new sysctl
setting if the new net namespace requires connection tracking, e.g. when
NAT rules are created.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This makes use of nf_ct_netns_get/put added in previous patch.
We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6
then implement use-count to track how many users (nft or xtables modules)
have a dependency on ipv4 and/or ipv6 connection tracking functionality.
When count reaches zero, the hooks are unregistered.
This delays activation of connection tracking inside a namespace until
stateful firewall rule or nat rule gets added.
This patch breaks backwards compatibility in the sense that connection
tracking won't be active anymore when the protocol tracker module is
loaded. This breaks e.g. setups that ctnetlink for flow accounting and
the like, without any '-m conntrack' packet filter rules.
Followup patch restores old behavour and makes new delayed scheme
optional via sysctl.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
so that conntrack core will add the needed hooks in this namespace.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
MASQUERADE, S/DNAT and REDIRECT already call functions that depend on the
conntrack module.
However, since the conntrack hooks are now registered in a lazy fashion
(i.e., only when needed) a symbol reference is not enough.
Thus, when something is added to a nat table, make sure that it will see
packets by calling nf_ct_netns_get() which will register the conntrack
hooks in the current netns.
An alternative would be to add these dependencies to the NAT table.
However, that has problems when using non-modular builds -- we might
register e.g. ipv6 conntrack before its initcall has run, leading to NULL
deref crashes since its per-netns storage has not yet been allocated.
Adding the dependency in the modules instead has the advantage that nat
table also does not register its hooks until rules are added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
currently aliased to try_module_get/_put.
Will be changed in next patch when we add functions to make use of ->net
argument to store usercount per l3proto tracker.
This is needed to avoid registering the conntrack hooks in all netns and
later only enable connection tracking in those that need conntrack.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
since adf0516845bcd0 ("netfilter: remove ip_conntrack* sysctl compat code")
the only user (ipv4 tracker) sets this to an empty stub function.
After this change nf_ct_l3proto_pernet_register() is also empty,
but this will change in a followup patch to add conditional register
of the hooks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y,
connection tracking support for UDPlite protocol is built-in into
nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| udplite| ipv4 | ipv6 |nf_conntrack
---------++--------+--------+--------+--------------
none || 432538 | 828755 | 828676 | 6141434
UDPlite || - | 829649 | 829362 | 6498204
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection
tracking support for SCTP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| sctp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 498243 | 828755 | 828676 | 6141434
SCTP || - | 829254 | 829175 | 6547872
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_CT_PROTO_DCCP is no more a tristate. When set to y, connection
tracking support for DCCP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_dccp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| dccp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 469140 | 828755 | 828676 | 6141434
DCCP || - | 830566 | 829935 | 6533526
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-next
Simon Horman says:
====================
IPVS Updates for v4.10
please consider these enhancements to the IPVS for v4.10.
* Decrement the IP ttl in all the modes in order to prevent infinite
route loops. Thanks to Dwip Banerjee.
* Use IS_ERR_OR_NULL macro. Clean-up from Gao Feng.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
So we can autoload nfnetlink_log.ko when the user adding nft log
group X rule in netdev family.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In netdev family, we will handle non ethernet packets, so using
eth_hdr(skb)->h_proto is incorrect.
Meanwhile, we can use socket(AF_PACKET...) to sending packets, so
skb->protocol is not always set in bridge family.
Add an extra parameter into nf_log_l2packet to solve this issue.
Fixes: 1fddf4bad0ac ("netfilter: nf_log: add packet logging for netdev family")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_NAT_PROTO_UDPLITE is no more a tristate. When set to y, NAT
support for UDPlite protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) |udplite || nf_nat
--------------------------+--------++--------
no builtin | 408048 || 2241312
UDPLITE builtin | - || 2577256
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_NAT_PROTO_SCTP is no more a tristate. When set to y, NAT
support for SCTP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | sctp || nf_nat
--------------------------+--------++--------
no builtin | 428344 || 2241312
SCTP builtin | - || 2597032
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_NAT_PROTO_DCCP is no more a tristate. When set to y, NAT
support for DCCP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | dccp || nf_nat
--------------------------+--------++--------
no builtin | 409800 || 2241312
DCCP builtin | - || 2578968
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The email address has changed, let's update the copyright statements.
Signed-off-by: Arturo Borrero Gonzalez <arturo@debian.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In function dcbnl_cee_fill(), returns the value of variable err on
errors. However, on some error paths (e.g. nla put fails), its value may
be 0. It may be better to explicitly set a negative errno to variable
err before returning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188881
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b90eb7549499 ("fib: introduce FIB notification infrastructure")
introduced a new notification chain to notify listeners (f.e., switchdev
drivers) about addition and deletion of routes.
However, upon registration to the chain the FIB tables can already be
populated, which means potential listeners will have an incomplete view
of the tables.
Solve that by dumping the FIB tables and replaying the events to the
passed notification block. The dump itself is done using RCU in order
not to starve consumers that need RTNL to make progress.
The integrity of the dump is ensured by reading the FIB change sequence
counter before and after the dump under RTNL. This allows us to avoid
the problematic situation in which the dumping process sends a ENTRY_ADD
notification following ENTRY_DEL generated by another process holding
RTNL.
Callers of the registration function may pass a callback that is
executed in case the dump was inconsistent with current FIB tables.
The number of retries until a consistent dump is achieved is set to a
fixed number to prevent callers from looping for long periods of time.
In case current limit proves to be problematic in the future, it can be
easily converted to be configurable using a sysctl.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch will enable listeners of the FIB notification chain to
request a dump of the FIB tables. However, since RTNL isn't taken during
the dump, it's possible for the FIB tables to change mid-dump, which
will result in inconsistency between the listener's table and the
kernel's.
Allow listeners to know about changes that occurred mid-dump, by adding
a change sequence counter to each net namespace. The counter is
incremented just before a notification is sent in the FIB chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order not to hold RTNL for long periods of time we're going to dump
the FIB tables using RCU.
Convert the FIB notification chain to be atomic, as we can't block in
RCU critical sections.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FIB notification chain is going to be converted to an atomic chain,
which means switchdev drivers will have to offload FIB entries in
deferred work, as hardware operations entail sleeping.
However, while the work is queued fib info might be freed, so a
reference must be taken. To release the reference (and potentially free
the fib info) fib_info_put() will be called, which in turn calls
free_fib_info().
Export free_fib_info() so that modules will be able to invoke
fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 255cb30425c0 ("net/sched: act_mirred: Add new tc_action_ops get_dev()")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit 850cbaddb52d ("udp: use it's own memory accounting
schema"), the udp protocol allowed sk_rmem_alloc to grow beyond
the rcvbuf by the whole current packet's truesize. After said commit
we allow sk_rmem_alloc to exceed the rcvbuf only if the receive queue
is empty. As reported by Jesper this cause a performance regression
for some (small) values of rcvbuf.
This commit is intended to fix the regression restoring the old
handling of the rcvbuf limit.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Fixes: 850cbaddb52d ("udp: use it's own memory accounting schema")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
Here is another batman-adv bugfix:
- fix checking for failed allocation of TVLV blocks in TT local data,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under heavy stress, timer used in estimators tend to slowly be delayed
by a few jiffies, leading to inaccuracies.
Lets remember what was the last scheduled jiffies so that we get more
precise estimations, without having to add a multiply/divide in the loop
to account for the drifts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net_generic() function is both a) inline and b) used ~600 times.
It has the following code inside
...
ptr = ng->ptr[id - 1];
...
"id" is never compile time constant so compiler is forced to subtract 1.
And those decrements or LEA [r32 - 1] instructions add up.
We also start id'ing from 1 to catch bugs where pernet sybsystem id
is not initialized and 0. This is quite pointless idea (nothing will
work or immediate interference with first registered subsystem) in
general but it hints what needs to be done for code size reduction.
Namely, overlaying allocation of pointer array and fixed part of
structure in the beginning and using usual base-0 addressing.
Ids are just cookies, their exact values do not matter, so lets start
with 3 on x86_64.
Code size savings (oh boy): -4.2 KB
As usual, ignore the initial compiler stupidity part of the table.
add/remove: 0/0 grow/shrink: 12/670 up/down: 89/-4297 (-4208)
function old new delta
tipc_nametbl_insert_publ 1250 1270 +20
nlmclnt_lookup_host 686 703 +17
nfsd4_encode_fattr 5930 5941 +11
nfs_get_client 1050 1061 +11
register_pernet_operations 333 342 +9
tcf_mirred_init 843 849 +6
tcf_bpf_init 1143 1149 +6
gss_setup_upcall 990 994 +4
idmap_name_to_id 432 434 +2
ops_init 274 275 +1
nfsd_inject_forget_client 259 260 +1
nfs4_alloc_client 612 613 +1
tunnel_key_walker 164 163 -1
...
tipc_bcbase_select_primary 392 360 -32
mac80211_hwsim_new_radio 2808 2767 -41
ipip6_tunnel_ioctl 2228 2186 -42
tipc_bcast_rcv 715 672 -43
tipc_link_build_proto_msg 1140 1089 -51
nfsd4_lock 3851 3796 -55
tipc_mon_rcv 1012 956 -56
Total: Before=156643951, After=156639743, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is precursor to fixing "[id - 1]" bloat inside net_generic().
Name "s" is chosen to complement name "u" often used for dummy unions.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Publishing net_generic pointer is done with silly mistake: new array is
published BEFORE setting freshly acquired pernet subsystem pointer.
memcpy
rcu_assign_pointer
kfree_rcu
ng->ptr[id - 1] = data;
This bug was introduced with commit dec827d174d7f76c457238800183ca864a639365
("[NETNS]: The generic per-net pointers.") in the glorious days of
chopping networking stack into containers proper 8.5 years ago (whee...)
How it didn't trigger for so long?
Well, you need quite specific set of conditions:
*) race window opens once per pernet subsystem addition
(read: modprobe or boot)
*) not every pernet subsystem is eligible (need ->id and ->size)
*) not every pernet subsystem is vulnerable (need incorrect or absense
of ordering of register_pernet_sybsys() and actually using net_generic())
*) to hide the bug even more, default is to preallocate 13 pointers which
is actually quite a lot. You need IPv6, netfilter, bridging etc together
loaded to trigger reallocation in the first place. Trimmed down
config are OK.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CAP_NET_ADMIN users should not be allowed to set negative
sk_sndbuf or sk_rcvbuf values, as it can lead to various memory
corruptions, crashes, OOM...
Note that before commit 82981930125a ("net: cleanups in
sock_setsockopt()"), the bug was even more serious, since SO_SNDBUF
and SO_RCVBUF were vulnerable.
This needs to be backported to all known linux kernels.
Again, many thanks to syzkaller team for discovering this gem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
