Merge tag 'stm32-dt-for-v6.15-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt

STM32 DT for v6.15, round 1

Highlights:
----------

- MPU:
  - STM32MP13:
    - Add thermal support.
    - Add Priva E-Measuringbox board support based on sTM32MP133C SoC.
      It embeds Ethernet RMII with TI phy, SDCard, eMMC and some
      sensors.
    - Add support for DHCOR SoM and DHSBC rev.200 board:
      TPM interrupts and gpio reset + LDO2/LDO5 support.

  - STMP32MP15:
    - Add new Octavo support: LXA FairyTux 2 based on OSD32MP153C SiP.
      It contains eMMC for storage, a gigabit Ethernet, a CAN bus and
      a RS485 transceiver.
    - Add Plymovent AQM board based on STM32MP151 SoC. It embeds:
      ETH RMII, WLAN, BT, Sensors (CO2, PM, pressure), Audio (I2S),
      Storage (SDCard, eMMC).

  - STM32MP25:
    - Add STM32MP257F Discovery board: It embeds a STM32MP257FAL SoC,
      with 4GB of LPDDR4, 2*USB typeA, 1*USB3 typeC, 1*ETH,
      wifi/BT combo, DSI HDMI, LVDS connector ...

    - Introduce STM32MP23 SoC and add STM32MP235F Discovery board:
      It embeds a STM32MP235FAK SoC, with 4GB of LPDDR4, 2*USB typeA,
      1*USB3 typeC, 1*ETH, wifi/BT combo, DSI HDMI, LVDS connector ...

    - Introduce STM32MP21 SoC and STM32MP215F discovery board:
      It embeds a STM32MP235FAN SoC, with 2GB of LPDDR4,
      1*USB2 peripheral bus powered typeC, 1*ETH, wifi/BT combo,
      LCD 18bit connector, CSI camera connector, ...

* tag 'stm32-dt-for-v6.15-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (26 commits)
  arm64: dts: st: add stm32mp215f-dk board support
  dt-bindings: stm32: document stm32mp215f-dk board
  arm64: dts: st: introduce stm32mp21 SoCs family
  arm64: dts: st: add stm32mp235f-dk board support
  dt-bindings: stm32: document stm32mp235f-dk board
  arm64: dts: st: introduce stm32mp23 SoCs family
  dt-bindings: stm32: add STM32MP21 and STM32MP23 compatibles for syscon
  arm64: Kconfig: expand STM32 Armv8 SoC with STM32MP21/STM32MP23 SoCs family
  arm64: dts: st: add stm32mp257f-dk board support
  dt-bindings: stm32: document stm32mp257f-dk board
  ARM: dts: stm32: Add Plymovent AQM devicetree
  ARM: dts: stm32: Add pinmux groups for Plymovent AQM board
  dt-bindings: arm: stm32: Add Plymovent AQM board
  dt-bindings: sound: convert ICS-43432 binding to YAML
  ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC rev.200 board
  ARM: dts: stm32: use IRQ_TYPE_EDGE_FALLING on stm32mp157c-dk2
  ARM: dts: stm32: add usr3 LED node to stm32f769-disco
  ARM: dts: stm32: rename LEDs nodes for stm32f769-disco
  ARM: dts: stm32: add push button to stm32f746 Discovery board
  ARM: dts: stm32: add led to stm32f746 Discovery board
  ...

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

12 files changed, 1902 insertions, 5 deletions

diff --git a/arch/arm/boot/dts/st/Makefile b/arch/arm/boot/dts/st/Makefile
index b7d5d305cbbe..60d55516f723 100644
--- a/arch/arm/boot/dts/st/Makefile
+++ b/arch/arm/boot/dts/st/Makefile
@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32h743i-eval.dtb \
 	stm32h743i-disco.dtb \
 	stm32h750i-art-pi.dtb \
+	stm32mp133c-prihmb.dtb \
 	stm32mp135f-dhcor-dhsbc.dtb \
 	stm32mp135f-dk.dtb \
 	stm32mp151a-prtt1a.dtb \
@@ -37,8 +38,11 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32mp151a-dhcor-testbench.dtb \
 	stm32mp151c-mecio1r0.dtb \
 	stm32mp151c-mect1s.dtb \
+	stm32mp151c-plyaqm.dtb \
 	stm32mp153c-dhcom-drc02.dtb \
 	stm32mp153c-dhcor-drc-compact.dtb \
+	stm32mp153c-lxa-fairytux2-gen1.dtb \
+	stm32mp153c-lxa-fairytux2-gen2.dtb \
 	stm32mp153c-lxa-tac-gen3.dtb \
 	stm32mp153c-mecio1r1.dtb \
 	stm32mp157a-avenger96.dtb \
diff --git a/arch/arm/boot/dts/st/stm32f746-disco.dts b/arch/arm/boot/dts/st/stm32f746-disco.dts
index 087de6f09629..b57dbdce2f40 100644
--- a/arch/arm/boot/dts/st/stm32f746-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f746-disco.dts
@@ -78,6 +78,24 @@
 		serial0 = &usart1;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		led-usr {
+			gpios = <&gpioi 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		button-0 {
+			label = "User";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	usbotg_hs_phy: usb-phy {
 		#phy-cells = <0>;
 		compatible = "usb-nop-xceiv";
diff --git a/arch/arm/boot/dts/st/stm32f769-disco.dts b/arch/arm/boot/dts/st/stm32f769-disco.dts
index 52c5baf58ab9..535cfdc4681c 100644
--- a/arch/arm/boot/dts/st/stm32f769-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f769-disco.dts
@@ -79,13 +79,16 @@
 
 	leds {
 		compatible = "gpio-leds";
-		led-green {
+		led-usr2 {
 			gpios = <&gpioj 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
-		led-red {
+		led-usr1 {
 			gpios = <&gpioj 13 GPIO_ACTIVE_HIGH>;
 		};
+		led-usr3 {
+			gpios = <&gpioa 12 GPIO_ACTIVE_HIGH>;
+		};
 	};
 
 	gpio-keys {
diff --git a/arch/arm/boot/dts/st/stm32mp131.dtsi b/arch/arm/boot/dts/st/stm32mp131.dtsi
index 0019d12c3d3d..8512a6e46b33 100644
--- a/arch/arm/boot/dts/st/stm32mp131.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp131.dtsi
@@ -100,6 +100,31 @@
 		always-on;
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&dts>;
+
+			trips {
+				cpu_alert1: cpu-alert1 {
+					temperature = <85000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				cpu-crit {
+					temperature = <120000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -919,6 +944,16 @@
 			};
 		};
 
+		dts: thermal@50028000 {
+			compatible = "st,stm32-thermal";
+			reg = <0x50028000 0x100>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DTS>;
+			clock-names = "pclk";
+			#thermal-sensor-cells = <0>;
+			status = "disabled";
+		};
+
 		mdma: dma-controller@58000000 {
 			compatible = "st,stm32h7-mdma";
 			reg = <0x58000000 0x1000>;
diff --git a/arch/arm/boot/dts/st/stm32mp133c-prihmb.dts b/arch/arm/boot/dts/st/stm32mp133c-prihmb.dts
new file mode 100644
index 000000000000..663b6de1b814
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp133c-prihmb.dts
@@ -0,0 +1,496 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/st,stm32mp13-regulator.h>
+#include "stm32mp133.dtsi"
+#include "stm32mp13xc.dtsi"
+#include "stm32mp13-pinctrl.dtsi"
+
+/ {
+	model = "Priva E-Measuringbox board";
+	compatible = "pri,prihmb", "st,stm32mp133";
+
+	aliases {
+		ethernet0 = &ethernet1;
+		mdio-gpio0 = &mdio0;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+		serial1 = &usart6;
+		serial2 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	counter-0 {
+		compatible = "interrupt-counter";
+		gpios = <&gpioa 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		button-reset {
+			label = "reset-button";
+			linux,code = <BTN_1>;
+			gpios = <&gpioi 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+	led-controller-0 {
+		compatible = "pwm-leds-multicolor";
+
+		multi-led {
+			color = <LED_COLOR_ID_RGB>;
+			function = LED_FUNCTION_STATUS;
+			max-brightness = <255>;
+
+			led-red {
+				active-low;
+				color = <LED_COLOR_ID_RED>;
+				pwms = <&pwm2 2 1000000 1>;
+			};
+
+			led-green {
+				active-low;
+				color = <LED_COLOR_ID_GREEN>;
+				pwms = <&pwm1 1 1000000 1>;
+			};
+
+			led-blue {
+				active-low;
+				color = <LED_COLOR_ID_BLUE>;
+				pwms = <&pwm1 2 1000000 1>;
+			};
+		};
+	};
+
+	led-controller-1 {
+		compatible = "pwm-leds-multicolor";
+
+		multi-led {
+			color = <LED_COLOR_ID_RGB>;
+			function = LED_FUNCTION_STATUS;
+			max-brightness = <255>;
+
+			led-red {
+				active-low;
+				color = <LED_COLOR_ID_RED>;
+				pwms = <&pwm1 0 1000000 1>;
+			};
+
+			led-green {
+				active-low;
+				color = <LED_COLOR_ID_GREEN>;
+				pwms = <&pwm2 0 1000000 1>;
+			};
+
+			led-blue {
+				active-low;
+				color = <LED_COLOR_ID_BLUE>;
+				pwms = <&pwm2 1 1000000 1>;
+			};
+		};
+	};
+
+	/* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
+	 * stmmac MDC clock without reducing system bus rate, we need to use
+	 * gpio based MDIO bus.
+	 */
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpiog 2 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+
+		/* TI DP83TD510E */
+		phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-id2000.0181";
+			reg = <0>;
+			interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10>;
+			reset-deassert-us = <35>;
+		};
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x10000000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		optee@ce000000 {
+			reg = <0xce000000 0x02000000>;
+			no-map;
+		};
+	};
+};
+
+&adc_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc_1_pins_a>;
+	vdda-supply = <&reg_3v3>;
+	vref-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&adc1 {
+	status = "okay";
+
+	channel@0 { /* Fan current PC0*/
+		reg = <0>;
+		st,min-sample-time-ns = <10000>;  /* 10µs sampling time */
+	};
+	channel@11 { /* Fan voltage */
+		reg = <11>;
+		st,min-sample-time-ns = <10000>;  /* 10µs sampling time */
+	};
+	channel@15 { /* Supply voltage */
+		reg = <15>;
+		st,min-sample-time-ns = <10000>;  /* 10µs sampling time */
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet1 {
+	status = "okay";
+	pinctrl-0 = <&ethernet1_rmii_pins_a>;
+	pinctrl-1 = <&ethernet1_rmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	clock-frequency = <100000>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	board-sensor@48 {
+		compatible = "ti,tmp1075";
+		reg = <0x48>;
+		vs-supply = <&reg_3v3>;
+	};
+};
+
+&{i2c1_pins_a/pins} {
+	pinmux = <STM32_PINMUX('D', 3, AF5)>, /* I2C1_SCL */
+		 <STM32_PINMUX('B', 8, AF4)>; /* I2C1_SDA */
+	bias-disable;
+	drive-open-drain;
+	slew-rate = <0>;
+};
+
+&{i2c1_sleep_pins_a/pins} {
+	pinmux = <STM32_PINMUX('D', 3, ANALOG)>, /* I2C1_SCL */
+		 <STM32_PINMUX('B', 8, ANALOG)>; /* I2C1_SDA */
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+/* SD card without Card-detect */
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+/* EMMC */
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	mmc-ddr-3_3v;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&timers1 {
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pwm1: pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
+
+&timers4 {
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pwm2: pwm {
+		pinctrl-0 = <&pwm4_pins_a>;
+		pinctrl-1 = <&pwm4_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
+
+/* Fan PWM */
+&timers5 {
+	status = "okay";
+
+	pwm3: pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
+
+&timers2 {
+	status = "okay";
+
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart7_pins_a>;
+	pinctrl-1 = <&uart7_sleep_pins_a>;
+	pinctrl-2 = <&uart7_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart6 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart6_pins_a>;
+	pinctrl-1 = <&usart6_sleep_pins_a>;
+	pinctrl-2 = <&usart6_idle_pins_a>;
+	linux,rs485-enabled-at-boot-time;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&pinctrl {
+	adc_1_pins_a: adc1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* ADC1 in0 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ADC1 in15 */
+				 <STM32_PINMUX('F', 13, ANALOG)>; /* ADC1 in11 */
+		};
+	};
+
+	ethernet1_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF11)>;   /* ETH1_RMII_REF_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	ethernet1_rmii_sleep_pins_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+
+	pwm1_pins_a: pwm1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, AF1)>, /* TIM1_CH1 */
+				 <STM32_PINMUX('E', 11, AF1)>, /* TIM1_CH2 */
+				 <STM32_PINMUX('E', 13, AF1)>; /* TIM1_CH3 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm1_sleep_pins_a: pwm1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, ANALOG)>, /* TIM1_CH1 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* TIM1_CH2 */
+				 <STM32_PINMUX('E', 13, ANALOG)>; /* TIM1_CH3 */
+		};
+	};
+
+	pwm4_pins_a: pwm4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, AF2)>, /* TIM4_CH1 */
+				 <STM32_PINMUX('B', 7, AF2)>, /* TIM4_CH2 */
+				 <STM32_PINMUX('D', 14, AF2)>; /* TIM4_CH3 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm4_sleep_pins_a: pwm4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* TIM4_CH1 */
+				 <STM32_PINMUX('B', 7, ANALOG)>, /* TIM4_CH2 */
+				 <STM32_PINMUX('D', 14, ANALOG)>; /* TIM4_CH3 */
+		};
+	};
+	pwm5_pins_a: pwm5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+		};
+	};
+
+	pwm5_sleep_pins_a: pwm5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
+		};
+	};
+
+	uart7_pins_a: uart7-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart7_idle_pins_a: uart7-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, ANALOG)>; /* UART7_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart7_sleep_pins_a: uart7-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 8, ANALOG)>, /* UART7_TX */
+				 <STM32_PINMUX('E', 10, ANALOG)>; /* UART7_RX */
+		};
+	};
+
+	usart6_pins_a: usart6-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 8, AF7)>, /* USART6_TX */
+				 <STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
+			bias-disable;
+		};
+	};
+
+	usart6_idle_pins_a: usart6-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 8, ANALOG)>; /* USART6_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
+			bias-disable;
+		};
+	};
+
+	usart6_sleep_pins_a: usart6-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* USART6_TX */
+				 <STM32_PINMUX('F', 10, ANALOG)>, /* USART6_DE */
+				 <STM32_PINMUX('H', 11, ANALOG)>; /* USART6_RX */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
index 853dc21449d9..9902849ed040 100644
--- a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
+++ b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
@@ -176,7 +176,7 @@
 	gpio-line-names = "", "", "", "",
 			  "", "DHSBC_USB_PWR_CC1", "", "",
 			  "", "", "", "DHSBC_nETH1_RST",
-			  "", "DHCOR_HW-CODING_0", "", "";
+			  "", "DHCOR_HW-CODING_0", "", "DHSBC_HW-CODE_2";
 };
 
 &gpiob {
@@ -197,7 +197,7 @@
 	gpio-line-names = "", "", "", "",
 			  "", "DHCOR_RAM-CODING_0", "", "",
 			  "", "DHCOR_RAM-CODING_1", "", "",
-			  "", "", "", "";
+			  "", "DHSBC_HW-CODE_1", "", "";
 };
 
 &gpioe {
@@ -221,6 +221,13 @@
 			  "DHSBC_ETH1_INTB", "", "", "DHSBC_ETH2_INTB";
 };
 
+&gpioh {
+	gpio-line-names = "", "", "", "DHSBC_HW-CODE_0",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
 &gpioi {
 	gpio-line-names = "DHCOR_RTC_nINT", "DHCOR_HW-CODING_1",
 			  "DHCOR_BT_REG_ON", "DHCOR_PMIC_nINT",
@@ -296,6 +303,9 @@
 	st33htph: tpm@0 {
 		compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
 		reg = <0>;
+		interrupt-parent = <&gpioe>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioe 12 GPIO_ACTIVE_LOW>;
 		spi-max-frequency = <24000000>;
 	};
 };
@@ -419,3 +429,19 @@
 		type = "micro";
 	};
 };
+
+/* LDO2 is expansion connector 3V3 supply on STM32MP13xx DHCOR DHSBC rev.200 */
+&vdd_ldo2 {
+	regulator-always-on;
+	regulator-boot-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+/* LDO5 is carrier board 3V3 supply on STM32MP13xx DHCOR DHSBC rev.200 */
+&vdd_sd {
+	regulator-always-on;
+	regulator-boot-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
index 95fafc51a1c8..40605ea85ee1 100644
--- a/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
@@ -26,6 +26,13 @@
 	};
 
 	/omit-if-no-ref/
+	adc1_in10_pins_a: adc1-in10-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>;
+		};
+	};
+
+	/omit-if-no-ref/
 	adc12_ain_pins_a: adc12-ain-0 {
 		pins {
 			pinmux = <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1 in13 */
@@ -585,6 +592,43 @@
 	};
 
 	/omit-if-no-ref/
+	ethernet0_rmii_pins_d: rmii-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 12, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('B', 13, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rmii_sleep_pins_d: rmii-sleep-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 12, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('B', 13, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */
+		};
+	};
+
+	/omit-if-no-ref/
 	fmc_pins_a: fmc-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
@@ -726,6 +770,25 @@
 	};
 
 	/omit-if-no-ref/
+	i2c1_pins_c: i2c1-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('D', 13, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c1_sleep_pins_c: i2c1-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('D', 13, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
 	i2c2_pins_a: i2c2-0 {
 		pins {
 			pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */
@@ -820,6 +883,27 @@
 	};
 
 	/omit-if-no-ref/
+	i2s1_pins_a: i2s1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 6, AF5)>, /* I2S2_SDI */
+				 <STM32_PINMUX('A', 4, AF5)>, /* I2S2_WS */
+				 <STM32_PINMUX('A', 5, AF5)>; /* I2S2_CK */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2s1_sleep_pins_a: i2s1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 6, ANALOG)>, /* I2S2_SDI */
+				 <STM32_PINMUX('A', 4, ANALOG)>, /* I2S2_WS */
+				 <STM32_PINMUX('A', 5, ANALOG)>; /* I2S2_CK */
+		};
+	};
+
+	/omit-if-no-ref/
 	i2s2_pins_a: i2s2-0 {
 		pins {
 			pinmux = <STM32_PINMUX('I', 3, AF5)>, /* I2S2_SDO */
@@ -1419,6 +1503,23 @@
 	};
 
 	/omit-if-no-ref/
+	pwm1_pins_d: pwm1-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm1_sleep_pins_d: pwm1-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 0, ANALOG)>;
+		};
+	};
+
+	/omit-if-no-ref/
 	pwm2_pins_a: pwm2-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
@@ -2161,6 +2262,66 @@
 	};
 
 	/omit-if-no-ref/
+	sdmmc2_b4_pins_c: sdmmc2-b4-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_b4_od_pins_c: sdmmc2-b4-od-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+
+		pins3 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_b4_sleep_pins_c: sdmmc2-b4-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+				 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
 	sdmmc2_d47_pins_a: sdmmc2-d47-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
@@ -2390,6 +2551,66 @@
 	};
 
 	/omit-if-no-ref/
+	sdmmc3_b4_pins_c: sdmmc3-b4-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_od_pins_c: sdmmc3-b4-od-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_sleep_pins_c: sdmmc3-b4-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('D', 4, ANALOG)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+				 <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
 	spdifrx_pins_a: spdifrx-0 {
 		pins {
 			pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
@@ -2601,6 +2822,41 @@
 	};
 
 	/omit-if-no-ref/
+	uart4_pins_e: uart4-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 8, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_idle_pins_e: uart4-idle-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, ANALOG)>; /* UART4_TX */
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 8, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_sleep_pins_e: uart4-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 11, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('B', 8, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	/omit-if-no-ref/
 	uart5_pins_a: uart5-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('B', 13, AF14)>; /* UART5_TX */
@@ -2678,6 +2934,23 @@
 	};
 
 	/omit-if-no-ref/
+	uart7_pins_d: uart7-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 7, AF7)>, /* UART7_TX */
+				 <STM32_PINMUX('F', 8, AF7)>; /* UART7_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART7_RX */
+				 <STM32_PINMUX('F', 9, AF7)>; /* UART7_CTS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
 	uart8_pins_a: uart8-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
@@ -3119,6 +3392,25 @@
 	};
 
 	/omit-if-no-ref/
+	i2c6_pins_b: i2c6-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, AF2)>, /* I2C6_SCL */
+				 <STM32_PINMUX('A', 12, AF2)>; /* I2C6_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c6_sleep_pins_b: i2c6-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* I2C6_SCL */
+				 <STM32_PINMUX('A', 12, ANALOG)>; /* I2C6_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
 	spi1_pins_a: spi1-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('Z', 0, AF5)>, /* SPI1_SCK */
diff --git a/arch/arm/boot/dts/st/stm32mp151c-plyaqm.dts b/arch/arm/boot/dts/st/stm32mp151c-plyaqm.dts
new file mode 100644
index 000000000000..39a3211c6133
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151c-plyaqm.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/dts-v1/;
+
+#include <arm/st/stm32mp151.dtsi>
+#include <arm/st/stm32mp15xc.dtsi>
+#include <arm/st/stm32mp15-pinctrl.dtsi>
+#include <arm/st/stm32mp15xxad-pinctrl.dtsi>
+#include <arm/st/stm32mp15-scmi.dtsi>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Plymovent AQM board";
+	compatible = "ply,plyaqm", "st,stm32mp151";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+		serial1 = &uart7;
+	};
+
+	codec {
+		compatible = "invensense,ics43432";
+
+		port {
+			codec_endpoint: endpoint {
+				remote-endpoint = <&i2s1_endpoint>;
+				dai-format = "i2s";
+			};
+		};
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			gpios = <&gpioa 3 GPIO_ACTIVE_HIGH>; /* WHITE_EN */
+			color = <LED_COLOR_ID_WHITE>;
+			default-state = "on";
+		};
+	};
+
+	v3v3: fixed-regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	v5v_sw: fixed-regulator-v5sw {
+		compatible = "regulator-fixed";
+		regulator-name = "5v-switched";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpioe 10 GPIO_ACTIVE_HIGH>; /* 5V_SWITCHED_EN */
+		startup-delay-us = <100000>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		optee@cfd00000 {
+			reg = <0xcfd00000 0x300000>;
+			no-map;
+		};
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP15";
+		dais = <&i2s1_port>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpioe 12 GPIO_ACTIVE_LOW>; /* WLAN_REG_ON */
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc1_in10_pins_a>;
+	vdda-supply = <&v3v3>;
+	vref-supply = <&v3v3>;
+	status = "okay";
+
+	adc@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		channel@10 { /* NTC */
+			reg = <10>;
+			st,min-sample-time-ns = <10000>;  /* 10µs sampling time */
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+	status = "okay";
+};
+
+&ethernet0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ethernet0_rmii_pins_d>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_d>;
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		/* KSZ8081RNA PHY */
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpiob 0 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpiob 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "HWID_PL_N", "HWID_CP", "";
+};
+
+&gpiob {
+	gpio-line-names =
+		"", "", "", "", "", "", "LED_LATCH", "",
+		"", "RELAY1_EN", "", "", "", "", "", "";
+};
+
+&gpioc {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "HWID_Q7", "", "";
+};
+
+&gpioe {
+	gpio-line-names =
+		"", "", "", "", "RELAY2_EN", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "SW1",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_c>;
+	pinctrl-1 = <&i2c1_sleep_pins_c>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&i2c6 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c6_pins_b>;
+	pinctrl-1 = <&i2c6_sleep_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clocks = <&scmi_clk CK_SCMI_I2C6>;
+	resets = <&scmi_reset RST_SCMI_I2C6>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pressure-sensor@47 {
+		compatible = "bosch,bmp580";
+		reg = <0x47>;
+		vdda-supply = <&v5v_sw>;
+		vddd-supply = <&v5v_sw>;
+	};
+
+	co2-sensor@62 {
+		compatible = "sensirion,scd41";
+		reg = <0x62>;
+		vdd-supply = <&v5v_sw>;
+	};
+
+	pm-sensor@69 {
+		compatible = "sensirion,sps30";
+		reg = <0x69>;
+	};
+};
+
+&i2s1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s1_pins_a>;
+	pinctrl-1 = <&i2s1_sleep_pins_a>;
+	clocks = <&rcc SPI1>, <&rcc SPI1_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	#clock-cells = <0>; /* Set I2S2 as master clock provider */
+	status = "okay";
+
+	i2s1_port: port {
+		i2s1_endpoint: endpoint {
+			format = "i2s";
+			mclk-fs = <256>;
+			remote-endpoint = <&codec_endpoint>;
+		};
+	};
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+	status = "okay";
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names =  "mcu_rst", "hold_boot";
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+	status = "okay";
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
+
+/* SD card without Card-detect */
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+/* EMMC */
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_c &sdmmc2_d47_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_c &sdmmc2_d47_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_c &sdmmc2_d47_sleep_pins_b>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+/* Wifi */
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_c>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_c>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_c>;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&timers5 {
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pwm {
+		pinctrl-0 = <&pwm1_pins_d>;
+		pinctrl-1 = <&pwm1_sleep_pins_d>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_e>;
+	pinctrl-1 = <&uart4_idle_pins_e>;
+	pinctrl-2 = <&uart4_sleep_pins_e>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_d>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpioe 11 GPIO_ACTIVE_HIGH>; /* BT_REG_ON */
+		max-speed = <4000000>;
+		vbat-supply = <&v3v3>;
+		vddio-supply = <&v3v3>;
+		interrupt-parent = <&gpiog>;
+		interrupts = <12 IRQ_TYPE_EDGE_RISING>; /* BT_HOST_WAKE */
+		interrupt-names = "host-wakeup";
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen1.dts b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen1.dts
new file mode 100644
index 000000000000..3a0e84262424
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen1.dts
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2024 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp153c-lxa-fairytux2.dtsi"
+
+/ {
+	model = "Linux Automation GmbH FairyTux 2 Gen 1";
+	compatible = "lxa,stm32mp153c-fairytux2-gen1", "oct,stm32mp153x-osd32", "st,stm32mp153";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-left {
+			label = "USER_BTN1";
+			linux,code = <KEY_ESC>;
+			gpios = <&gpioi 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+
+		button-right {
+			label = "USER_BTN2";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpioe 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+	};
+};
+
+&gpiof {
+	gpio-line-names = "GPIO1", "GPIO2", "", "", "",			/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "", "", "",				/* 10 */
+			  "";						/* 15 */
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "", "LCD_RESET",			/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "", "GPIO3", "",			/* 10 */
+			  "";						/* 15 */
+};
+
+&gpioi {
+	gpio-line-names = "", "", "", "", "",				/*  0 */
+			  "", "", "", "ETH_", "",			/*  5 */
+			  "", "USER_BTN1";				/* 10 */
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-1 = <&i2c1_sleep_pins_b>;
+	status = "okay";
+
+	io_board_gpio: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&v3v3_hdmi>;
+		gpio-line-names = "LED1_GA_YK", "LED2_GA_YK", "LED1_GK_YA", "LED2_GK_YA",
+				  "RS485_EN", "RS485_120R", "", "CAN_120R";
+	};
+};
+
+&led_controller_io {
+	/*
+	 * led-2 and led-3 are internally connected antiparallel to one
+	 * another inside the ethernet jack like this:
+	 * GPIO1 ---+---|led-2|>--+--- GPIO3
+	 *          +--<|led-3|---+
+	 * E.g. only one of the LEDs can be illuminated at a time while
+	 * the other output must be driven low.
+	 * This should likely be implemented using a multi color LED
+	 * driver for antiparallel LEDs.
+	 */
+	led-2 {
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_ACTIVITY;
+		gpios = <&io_board_gpio 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	led-3 {
+		color = <LED_COLOR_ID_ORANGE>;
+		function = LED_FUNCTION_ACTIVITY;
+		gpios = <&io_board_gpio 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usart3 {
+	/*
+	 * On Gen 1 FairyTux 2 only RTS can be used and not CTS as well,
+	 * Because pins PD11 (CTS) and PI11 (USER_BTN1) share the same
+	 * interrupt and only one of them can be used at a time.
+	 */
+	rts-gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts
new file mode 100644
index 000000000000..66e6da912508
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2024 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp153c-lxa-fairytux2.dtsi"
+
+/ {
+	model = "Linux Automation GmbH FairyTux 2 Gen 2";
+	compatible = "lxa,stm32mp153c-fairytux2-gen2", "oct,stm32mp153x-osd32", "st,stm32mp153";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-left {
+			label = "USER_BTN1";
+			linux,code = <KEY_ESC>;
+			gpios = <&gpioi 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+
+		button-right {
+			label = "USER_BTN2";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpioe 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+	};
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "", "",				/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "", "", "",				/* 10 */
+			  "";						/* 15 */
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "", "LCD_RESET",			/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "GPIO1", "GPIO_INT", "",		/* 10 */
+			  "";						/* 15 */
+};
+
+&gpioi {
+	gpio-line-names = "GPIO2", "", "", "", "",			/*  0 */
+			  "", "", "", "ETH_", "",			/*  5 */
+			  "", "USER_BTN1";				/* 10 */
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-1 = <&i2c1_sleep_pins_b>;
+	status = "okay";
+
+	io_board_gpio: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpioh>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&board_tca6408_pins>;
+		#interrupt-cells = <2>;
+		vcc-supply = <&v3v3_hdmi>;
+		gpio-line-names = "LED1_GA_YK", "LED2_GA_YK", "LED1_GK_YA", "USB_CC_ALERT",
+				  "RS485_EN", "RS485_120R", "USB_CC_RESET", "CAN_120R";
+	};
+
+	usb_c: typec@28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupt-parent = <&io_board_gpio>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&reg_5v>;
+		vsys-supply = <&v3v3_hdmi>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			typec-power-opmode = "default";
+
+			port {
+				con_usbotg_hs_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+
+	temperature-sensor@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+		/*
+		 * The sensor itself is powered by a voltage divider from the
+		 * always-on 5V supply.
+		 * The required pull-up resistors however are on v3v3_hdmi.
+		 */
+		vs-supply = <&v3v3_hdmi>;
+	};
+
+	io_board_eeprom: eeprom@56 {
+		compatible = "atmel,24c04";
+		reg = <0x56>;
+		vcc-supply = <&v3v3_hdmi>;
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&led_controller_io {
+	led-2 {
+		color = <LED_COLOR_ID_ORANGE>;
+		function = LED_FUNCTION_ACTIVITY;
+		gpios = <&io_board_gpio 1 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&usart3 {
+	rts-gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpiod 11 GPIO_ACTIVE_LOW>;
+};
+
+&usbotg_hs {
+	usb-role-switch;
+
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usbotg_hs_ep>;
+		};
+	};
+};
+
+&pinctrl {
+	board_tca6408_pins: stusb1600-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 13, GPIO)>;
+			bias-pull-up;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi
new file mode 100644
index 000000000000..9eeb9d6b5eb0
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi
@@ -0,0 +1,397 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023, 2024 Leonard Göhrs, Pengutronix
+ */
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		can0 = &m_can1;
+		ethernet0 = &ethernet0;
+		i2c0 = &i2c1;
+		i2c1 = &i2c4;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+		serial1 = &usart3;
+		spi0 = &spi4;
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&v3v3>;
+
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		pwms = <&led_pwm 3 1000000 0>;
+	};
+
+	led-controller-cpu {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	led_controller_io: led-controller-io {
+		compatible = "gpio-leds";
+
+		/*
+		 * led-0 and led-1 are internally connected antiparallel to one
+		 * another inside the ethernet jack like this:
+		 * GPIO0 ---+---|led-0|>--+--- GPIO2
+		 *          +--<|led-1|---+
+		 * E.g. only one of the LEDs can be illuminated at a time while
+		 * the other output must be driven low.
+		 * This should likely be implemented using a multi color LED
+		 * driver for antiparallel LEDs.
+		 */
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			gpios = <&io_board_gpio 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_ORANGE>;
+			function = LED_FUNCTION_LAN;
+			gpios = <&io_board_gpio 2 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_1v2: regulator-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_5v>;
+	};
+};
+
+baseboard_eeprom: &sip_eeprom {
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_b>;
+
+	st,eth-clk-sel;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@3 { /* KSZ9031RN */
+			reg = <3>;
+			reset-gpios = <&gpioe 11 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+			interrupt-parent = <&gpioa>;
+			interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+			micrel,force-master;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "", "",				/*  0 */
+			  "", "ETH_INT", "", "", "",			/*  5 */
+			  "", "", "", "BOOTROM_LED", "",		/* 10 */
+			  "";						/* 15 */
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "", "",				/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "", "", "",				/* 10 */
+			  "";						/* 15 */
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "", "",				/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "";					/* 10 */
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "", "",				/*  0 */
+			  "", "", "LCD_TE", "", "",			/*  5 */
+			  "LCD_DC", "", "", "", "",			/* 10 */
+			  "";						/* 15 */
+};
+
+&gpioe {
+	gpio-line-names = "LCD_CS", "", "", "", "",			/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "", "", "",				/* 10 */
+			  "";						/* 15 */
+};
+
+&gpiof {
+	gpio-line-names = "GPIO1", "GPIO2", "", "", "",			/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "", "", "",				/* 10 */
+			  "";						/* 15 */
+};
+
+&gpiog {
+	gpio-line-names = "", "", "", "", "",				/*  0 */
+			  "", "", "", "", "",				/*  5 */
+			  "", "", "", "", "",				/* 10 */
+			  "";						/* 15 */
+};
+
+&gpioz {
+	gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "",	/*  0 */
+			  "", "HWID4", "HWID5";				/*  5 */
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <8>;
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "okay";
+	termination-gpios = <&io_board_gpio 7 GPIO_ACTIVE_HIGH>;
+	termination-ohms = <120>;
+};
+
+&pmic {
+	regulators {
+		buck1-supply = <&reg_5v>;	/* VIN */
+		buck2-supply = <&reg_5v>;	/* VIN */
+		buck3-supply = <&reg_5v>;	/* VIN */
+		buck4-supply = <&reg_5v>;	/* VIN */
+		ldo2-supply = <&reg_5v>;	/* PMIC_LDO25IN */
+		ldo4-supply = <&reg_5v>;	/* VIN */
+		ldo5-supply = <&reg_5v>;	/* PMIC_LDO25IN */
+		vref_ddr-supply = <&reg_5v>;	/* VIN */
+		boost-supply = <&reg_5v>;	/* PMIC_BSTIN */
+		pwr_sw2-supply = <&bst_out>;	/* PMIC_SWIN */
+	};
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+	vmmc-supply = <&v3v3>;
+
+	bus-width = <8>;
+	mmc-ddr-3_3v;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+
+	status = "okay";
+};
+
+&spi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi4_pins_a>;
+	cs-gpios = <&gpioe 0 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	lcd: display@0 {
+		compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
+		reg = <0>;
+		power-supply = <&v3v3>;
+		io-supply = <&v3v3>;
+		backlight = <&backlight>;
+		dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
+		spi-3wire;
+		spi-max-frequency = <32000000>;
+
+		width-mm = <23>;
+		height-mm = <23>;
+		rotation = <180>;
+
+		panel-timing {
+			hactive = <240>;
+			vactive = <240>;
+			hback-porch = <0>;
+			vback-porch = <0>;
+
+			clock-frequency = <0>;
+			hfront-porch = <0>;
+			hsync-len = <0>;
+			vfront-porch = <0>;
+			vsync-len = <0>;
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	led_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm8_pins_b>;
+		pinctrl-1 = <&pwm8_sleep_pins_b>;
+		status = "okay";
+	};
+};
+
+&uart4 {
+	label = "debug";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+};
+
+&usart3 {
+	label = "external";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+
+	vusb_d-supply = <&vdd_usb>;
+	vusb_a-supply = <&reg18>;
+
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
+&v3v3_hdmi {
+	regulator-enable-ramp-delay = <1000>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dk2.dts b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
index 5f9c0160a9c4..324f7bb988d1 100644
--- a/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
+++ b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
@@ -67,7 +67,7 @@
 	touchscreen@38 {
 		compatible = "focaltech,ft6236";
 		reg = <0x38>;
-		interrupts = <2 2>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-parent = <&gpiof>;
 		touchscreen-size-x = <480>;
 		touchscreen-size-y = <800>;