summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
7 daysnet: enetc: do not print error log if addr is 0Wei Fang
A value of 0 for addr indicates that the IEB_LBCR register does not need to be configured, as its default value is 0. However, the driver will print an error log if addr is 0, so this issue needs to be fixed. Fixes: 50bfd9c06f0f ("net: enetc: set external PHY address in IERB for i.MX94 ENETC") Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20251222022628.4016403-1-wei.fang@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
7 daysnet: macb: Relocate mog_init_rings() callback from macb_mac_link_up() to ↵Xiaolei Wang
macb_open() In the non-RT kernel, local_bh_disable() merely disables preemption, whereas it maps to an actual spin lock in the RT kernel. Consequently, when attempting to refill RX buffers via netdev_alloc_skb() in macb_mac_link_up(), a deadlock scenario arises as follows: WARNING: possible circular locking dependency detected 6.18.0-08691-g2061f18ad76e #39 Not tainted ------------------------------------------------------ kworker/0:0/8 is trying to acquire lock: ffff00080369bbe0 (&bp->lock){+.+.}-{3:3}, at: macb_start_xmit+0x808/0xb7c but task is already holding lock: ffff000803698e58 (&queue->tx_ptr_lock){+...}-{3:3}, at: macb_start_xmit +0x148/0xb7c which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (&queue->tx_ptr_lock){+...}-{3:3}: rt_spin_lock+0x50/0x1f0 macb_start_xmit+0x148/0xb7c dev_hard_start_xmit+0x94/0x284 sch_direct_xmit+0x8c/0x37c __dev_queue_xmit+0x708/0x1120 neigh_resolve_output+0x148/0x28c ip6_finish_output2+0x2c0/0xb2c __ip6_finish_output+0x114/0x308 ip6_output+0xc4/0x4a4 mld_sendpack+0x220/0x68c mld_ifc_work+0x2a8/0x4f4 process_one_work+0x20c/0x5f8 worker_thread+0x1b0/0x35c kthread+0x144/0x200 ret_from_fork+0x10/0x20 -> #2 (_xmit_ETHER#2){+...}-{3:3}: rt_spin_lock+0x50/0x1f0 sch_direct_xmit+0x11c/0x37c __dev_queue_xmit+0x708/0x1120 neigh_resolve_output+0x148/0x28c ip6_finish_output2+0x2c0/0xb2c __ip6_finish_output+0x114/0x308 ip6_output+0xc4/0x4a4 mld_sendpack+0x220/0x68c mld_ifc_work+0x2a8/0x4f4 process_one_work+0x20c/0x5f8 worker_thread+0x1b0/0x35c kthread+0x144/0x200 ret_from_fork+0x10/0x20 -> #1 ((softirq_ctrl.lock)){+.+.}-{3:3}: lock_release+0x250/0x348 __local_bh_enable_ip+0x7c/0x240 __netdev_alloc_skb+0x1b4/0x1d8 gem_rx_refill+0xdc/0x240 gem_init_rings+0xb4/0x108 macb_mac_link_up+0x9c/0x2b4 phylink_resolve+0x170/0x614 process_one_work+0x20c/0x5f8 worker_thread+0x1b0/0x35c kthread+0x144/0x200 ret_from_fork+0x10/0x20 -> #0 (&bp->lock){+.+.}-{3:3}: __lock_acquire+0x15a8/0x2084 lock_acquire+0x1cc/0x350 rt_spin_lock+0x50/0x1f0 macb_start_xmit+0x808/0xb7c dev_hard_start_xmit+0x94/0x284 sch_direct_xmit+0x8c/0x37c __dev_queue_xmit+0x708/0x1120 neigh_resolve_output+0x148/0x28c ip6_finish_output2+0x2c0/0xb2c __ip6_finish_output+0x114/0x308 ip6_output+0xc4/0x4a4 mld_sendpack+0x220/0x68c mld_ifc_work+0x2a8/0x4f4 process_one_work+0x20c/0x5f8 worker_thread+0x1b0/0x35c kthread+0x144/0x200 ret_from_fork+0x10/0x20 other info that might help us debug this: Chain exists of: &bp->lock --> _xmit_ETHER#2 --> &queue->tx_ptr_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&queue->tx_ptr_lock); lock(_xmit_ETHER#2); lock(&queue->tx_ptr_lock); lock(&bp->lock); *** DEADLOCK *** Call trace: show_stack+0x18/0x24 (C) dump_stack_lvl+0xa0/0xf0 dump_stack+0x18/0x24 print_circular_bug+0x28c/0x370 check_noncircular+0x198/0x1ac __lock_acquire+0x15a8/0x2084 lock_acquire+0x1cc/0x350 rt_spin_lock+0x50/0x1f0 macb_start_xmit+0x808/0xb7c dev_hard_start_xmit+0x94/0x284 sch_direct_xmit+0x8c/0x37c __dev_queue_xmit+0x708/0x1120 neigh_resolve_output+0x148/0x28c ip6_finish_output2+0x2c0/0xb2c __ip6_finish_output+0x114/0x308 ip6_output+0xc4/0x4a4 mld_sendpack+0x220/0x68c mld_ifc_work+0x2a8/0x4f4 process_one_work+0x20c/0x5f8 worker_thread+0x1b0/0x35c kthread+0x144/0x200 ret_from_fork+0x10/0x20 Notably, invoking the mog_init_rings() callback upon link establishment is unnecessary. Instead, we can exclusively call mog_init_rings() within the ndo_open() callback. This adjustment resolves the deadlock issue. Furthermore, since MACB_CAPS_MACB_IS_EMAC cases do not use mog_init_rings() when opening the network interface via at91ether_open(), moving mog_init_rings() to macb_open() also eliminates the MACB_CAPS_MACB_IS_EMAC check. Fixes: 633e98a711ac ("net: macb: use resolved link config in mac_link_up()") Cc: stable@vger.kernel.org Suggested-by: Kevin Hao <kexin.hao@windriver.com> Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Link: https://patch.msgid.link/20251222015624.1994551-1-xiaolei.wang@windriver.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
7 daysgve: defer interrupt enabling until NAPI registrationAnkit Garg
Currently, interrupts are automatically enabled immediately upon request. This allows interrupt to fire before the associated NAPI context is fully initialized and cause failures like below: [ 0.946369] Call Trace: [ 0.946369] <IRQ> [ 0.946369] __napi_poll+0x2a/0x1e0 [ 0.946369] net_rx_action+0x2f9/0x3f0 [ 0.946369] handle_softirqs+0xd6/0x2c0 [ 0.946369] ? handle_edge_irq+0xc1/0x1b0 [ 0.946369] __irq_exit_rcu+0xc3/0xe0 [ 0.946369] common_interrupt+0x81/0xa0 [ 0.946369] </IRQ> [ 0.946369] <TASK> [ 0.946369] asm_common_interrupt+0x22/0x40 [ 0.946369] RIP: 0010:pv_native_safe_halt+0xb/0x10 Use the `IRQF_NO_AUTOEN` flag when requesting interrupts to prevent auto enablement and explicitly enable the interrupt in NAPI initialization path (and disable it during NAPI teardown). This ensures that interrupt lifecycle is strictly coupled with readiness of NAPI context. Cc: stable@vger.kernel.org Fixes: 1dfc2e46117e ("gve: Refactor napi add and remove functions") Signed-off-by: Ankit Garg <nktgrg@google.com> Reviewed-by: Jordan Rhee <jordanrhee@google.com> Reviewed-by: Joshua Washington <joshwash@google.com> Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com> Link: https://patch.msgid.link/20251219102945.2193617-1-hramamurthy@google.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
7 daysnet: stmmac: fix the crash issue for zero copy XDP_TX actionWei Fang
There is a crash issue when running zero copy XDP_TX action, the crash log is shown below. [ 216.122464] Unable to handle kernel paging request at virtual address fffeffff80000000 [ 216.187524] Internal error: Oops: 0000000096000144 [#1] SMP [ 216.301694] Call trace: [ 216.304130] dcache_clean_poc+0x20/0x38 (P) [ 216.308308] __dma_sync_single_for_device+0x1bc/0x1e0 [ 216.313351] stmmac_xdp_xmit_xdpf+0x354/0x400 [ 216.317701] __stmmac_xdp_run_prog+0x164/0x368 [ 216.322139] stmmac_napi_poll_rxtx+0xba8/0xf00 [ 216.326576] __napi_poll+0x40/0x218 [ 216.408054] Kernel panic - not syncing: Oops: Fatal exception in interrupt For XDP_TX action, the xdp_buff is converted to xdp_frame by xdp_convert_buff_to_frame(). The memory type of the resulting xdp_frame depends on the memory type of the xdp_buff. For page pool based xdp_buff it produces xdp_frame with memory type MEM_TYPE_PAGE_POOL. For zero copy XSK pool based xdp_buff it produces xdp_frame with memory type MEM_TYPE_PAGE_ORDER0. However, stmmac_xdp_xmit_back() does not check the memory type and always uses the page pool type, this leads to invalid mappings and causes the crash. Therefore, check the xdp_buff memory type in stmmac_xdp_xmit_back() to fix this issue. Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy") Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Hariprasad Kelam <hkelam@marvell.com> Link: https://patch.msgid.link/20251204071332.1907111-1-wei.fang@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
7 daysocteontx2-pf: fix "UBSAN: shift-out-of-bounds error"Anshumali Gaur
This patch ensures that the RX ring size (rx_pending) is not set below the permitted length. This avoids UBSAN shift-out-of-bounds errors when users passes small or zero ring sizes via ethtool -G. Fixes: d45d8979840d ("octeontx2-pf: Add basic ethtool support") Signed-off-by: Anshumali Gaur <agaur@marvell.com> Link: https://patch.msgid.link/20251219062226.524844-1-agaur@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
9 daysnet: mana: Fix use-after-free in reset service rescan pathDipayaan Roy
When mana_serv_reset() encounters -ETIMEDOUT or -EPROTO from mana_gd_resume(), it performs a PCI rescan via mana_serv_rescan(). mana_serv_rescan() calls pci_stop_and_remove_bus_device(), which can invoke the driver's remove path and free the gdma_context associated with the device. After returning, mana_serv_reset() currently jumps to the out label and attempts to clear gc->in_service, dereferencing a freed gdma_context. The issue was observed with the following call logs: [ 698.942636] BUG: unable to handle page fault for address: ff6c2b638088508d [ 698.943121] #PF: supervisor write access in kernel mode [ 698.943423] #PF: error_code(0x0002) - not-present page [S[ 698.943793] Pat Dec 6 07:GD5 100000067 P4D 1002f7067 PUD 1002f8067 PMD 101bef067 PTE 0 0:56 2025] hv_[n e 698.944283] Oops: Oops: 0002 [#1] SMP NOPTI tvsc f8615163-00[ 698.944611] CPU: 28 UID: 0 PID: 249 Comm: kworker/28:1 ... [Sat Dec 6 07:50:56 2025] R10: [ 699.121594] mana 7870:00:00.0 enP30832s1: Configured vPort 0 PD 18 DB 16 000000000000001b R11: 0000000000000000 R12: ff44cf3f40270000 [Sat Dec 6 07:50:56 2025] R13: 0000000000000001 R14: ff44cf3f402700c8 R15: ff44cf3f4021b405 [Sat Dec 6 07:50:56 2025] FS: 0000000000000000(0000) GS:ff44cf7e9fcf9000(0000) knlGS:0000000000000000 [Sat Dec 6 07:50:56 2025] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [Sat Dec 6 07:50:56 2025] CR2: ff6c2b638088508d CR3: 000000011fe43001 CR4: 0000000000b73ef0 [Sat Dec 6 07:50:56 2025] Call Trace: [Sat Dec 6 07:50:56 2025] <TASK> [Sat Dec 6 07:50:56 2025] mana_serv_func+0x24/0x50 [mana] [Sat Dec 6 07:50:56 2025] process_one_work+0x190/0x350 [Sat Dec 6 07:50:56 2025] worker_thread+0x2b7/0x3d0 [Sat Dec 6 07:50:56 2025] kthread+0xf3/0x200 [Sat Dec 6 07:50:56 2025] ? __pfx_worker_thread+0x10/0x10 [Sat Dec 6 07:50:56 2025] ? __pfx_kthread+0x10/0x10 [Sat Dec 6 07:50:56 2025] ret_from_fork+0x21a/0x250 [Sat Dec 6 07:50:56 2025] ? __pfx_kthread+0x10/0x10 [Sat Dec 6 07:50:56 2025] ret_from_fork_asm+0x1a/0x30 [Sat Dec 6 07:50:56 2025] </TASK> Fix this by returning immediately after mana_serv_rescan() to avoid accessing GC state that may no longer be valid. Fixes: 9bf66036d686 ("net: mana: Handle hardware recovery events when probing the device") Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com> Link: https://patch.msgid.link/20251218131054.GA3173@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net Signed-off-by: Paolo Abeni <pabeni@redhat.com>
9 daysMerge branch '40GbE' of ↵Paolo Abeni
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2025-12-17 (i40e, iavf, idpf, e1000) For i40e: Przemyslaw immediately schedules service task following changes to filters to ensure timely setup for PTP. Gregory Herrero adjusts VF descriptor size checks to be device specific. For iavf: Kohei Enju corrects a couple of condition checks which caused off-by-one issues. For idpf: Larysa fixes LAN memory region call to follow expected requirements. Brian Vazquez reduces mailbox wait time during init to avoid lengthy delays. For e1000: Guangshuo Li adds validation of data length to prevent out-of-bounds access. * '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: e1000: fix OOB in e1000_tbi_should_accept() idpf: reduce mbx_task schedule delay to 300us idpf: fix LAN memory regions command on some NVMs iavf: fix off-by-one issues in iavf_config_rss_reg() i40e: validate ring_len parameter against hardware-specific values i40e: fix scheduling in set_rx_mode ==================== Link: https://patch.msgid.link/ Signed-off-by: Paolo Abeni <pabeni@redhat.com>
9 daysbng_en: update module descriptionRajashekar Hudumula
The Broadcom BCM57708/800G NIC family is branded as ThorUltra. Update the driver description accordingly. Fixes: 74715c4ab0fa0 ("bng_en: Add PCI interface") Signed-off-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com> Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com> Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com> Link: https://patch.msgid.link/20251217104748.3004706-1-rajashekar.hudumula@broadcom.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
13 dayssmc91x: fix broken irq-context in PREEMPT_RTYeoreum Yun
When smc91x.c is built with PREEMPT_RT, the following splat occurs in FVP_RevC: [ 13.055000] smc91x LNRO0003:00 eth0: link up, 10Mbps, half-duplex, lpa 0x0000 [ 13.062137] BUG: workqueue leaked atomic, lock or RCU: kworker/2:1[106] [ 13.062137] preempt=0x00000000 lock=0->0 RCU=0->1 workfn=mld_ifc_work [ 13.062266] C ** replaying previous printk message ** [ 13.062266] CPU: 2 UID: 0 PID: 106 Comm: kworker/2:1 Not tainted 6.18.0-dirty #179 PREEMPT_{RT,(full)} [ 13.062353] Hardware name: , BIOS [ 13.062382] Workqueue: mld mld_ifc_work [ 13.062469] Call trace: [ 13.062494] show_stack+0x24/0x40 (C) [ 13.062602] __dump_stack+0x28/0x48 [ 13.062710] dump_stack_lvl+0x7c/0xb0 [ 13.062818] dump_stack+0x18/0x34 [ 13.062926] process_scheduled_works+0x294/0x450 [ 13.063043] worker_thread+0x260/0x3d8 [ 13.063124] kthread+0x1c4/0x228 [ 13.063235] ret_from_fork+0x10/0x20 This happens because smc_special_trylock() disables IRQs even on PREEMPT_RT, but smc_special_unlock() does not restore IRQs on PREEMPT_RT. The reason is that smc_special_unlock() calls spin_unlock_irqrestore(), and rcu_read_unlock_bh() in __dev_queue_xmit() cannot invoke rcu_read_unlock() through __local_bh_enable_ip() when current->softirq_disable_cnt becomes zero. To address this issue, replace smc_special_trylock() with spin_trylock_irqsave(). Fixes: 342a93247e08 ("locking/spinlock: Provide RT variant header: <linux/spinlock_rt.h>") Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20251217085115.1730036-1-yeoreum.yun@arm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
14 daysnet: wangxun: move PHYLINK dependencyArnd Bergmann
The LIBWX library code is what calls into phylink, so any user of it has to select CONFIG_PHYLINK at the moment, with NGBEVF missing this: x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_nway_reset': wx_ethtool.c:(.text+0x613): undefined reference to `phylink_ethtool_nway_reset' x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_get_link_ksettings': wx_ethtool.c:(.text+0x62b): undefined reference to `phylink_ethtool_ksettings_get' x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_set_link_ksettings': wx_ethtool.c:(.text+0x643): undefined reference to `phylink_ethtool_ksettings_set' x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_get_pauseparam': wx_ethtool.c:(.text+0x65b): undefined reference to `phylink_ethtool_get_pauseparam' x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_set_pauseparam': wx_ethtool.c:(.text+0x677): undefined reference to `phylink_ethtool_set_pauseparam' Add the 'select PHYLINK' line in the libwx option directly so this will always be enabled for all current and future wangxun drivers, and remove the now duplicate lines. Fixes: a0008a3658a3 ("net: wangxun: add ngbevf build") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20251216213547.115026-1-arnd@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
14 daysamd-xgbe: reset retries and mode on RX adapt failuresRaju Rangoju
During the stress tests, early RX adaptation handshakes can fail, such as missing the RX_ADAPT ACK or not receiving a coefficient update before block lock is established. Continuing to retry RX adaptation in this state is often ineffective if the current mode selection is not viable. Resetting the RX adaptation retry counter when an RX_ADAPT request fails to receive ACK or a coefficient update prior to block lock, and clearing mode_set so the next bring-up performs a fresh mode selection rather than looping on a likely invalid configuration. Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Link: https://patch.msgid.link/20251215151728.311713-1-Raju.Rangoju@amd.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
14 daysnet: airoha: Move net_devs registration in a dedicated routineLorenzo Bianconi
Since airoha_probe() is not executed under rtnl lock, there is small race where a given device is configured by user-space while the remaining ones are not completely loaded from the dts yet. This condition will allow a hw device misconfiguration since there are some conditions (e.g. GDM2 check in airoha_dev_init()) that require all device are properly loaded from the device tree. Fix the issue moving net_devices registration at the end of the airoha_probe routine. Fixes: 9cd451d414f6e ("net: airoha: Add loopback support for GDM2") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20251214-airoha-fix-dev-registration-v1-1-860e027ad4c6@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-19Merge tag 'net-6.19-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from netfilter and CAN. Current release - regressions: - netfilter: nf_conncount: fix leaked ct in error paths - sched: act_mirred: fix loop detection - sctp: fix potential deadlock in sctp_clone_sock() - can: fix build dependency - eth: mlx5e: do not update BQL of old txqs during channel reconfiguration Previous releases - regressions: - sched: ets: always remove class from active list before deleting it - inet: frags: flush pending skbs in fqdir_pre_exit() - netfilter: nf_nat: remove bogus direction check - mptcp: - schedule rtx timer only after pushing data - avoid deadlock on fallback while reinjecting - can: gs_usb: fix error handling - eth: - mlx5e: - avoid unregistering PSP twice - fix double unregister of HCA_PORTS component - bnxt_en: fix XDP_TX path - mlxsw: fix use-after-free when updating multicast route stats Previous releases - always broken: - ethtool: avoid overflowing userspace buffer on stats query - openvswitch: fix middle attribute validation in push_nsh() action - eth: - mlx5: fw_tracer, validate format string parameters - mlxsw: spectrum_router: fix neighbour use-after-free - ipvlan: ignore PACKET_LOOPBACK in handle_mode_l2() Misc: - Jozsef Kadlecsik retires from maintaining netfilter - tools: ynl: fix build on systems with old kernel headers" * tag 'net-6.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits) net: hns3: add VLAN id validation before using net: hns3: using the num_tqps to check whether tqp_index is out of range when vf get ring info from mbx net: hns3: using the num_tqps in the vf driver to apply for resources net: enetc: do not transmit redirected XDP frames when the link is down selftests/tc-testing: Test case exercising potential mirred redirect deadlock net/sched: act_mirred: fix loop detection sctp: Clear inet_opt in sctp_v6_copy_ip_options(). sctp: Fetch inet6_sk() after setting ->pinet6 in sctp_clone_sock(). net/handshake: duplicate handshake cancellations leak socket net/mlx5e: Don't include PSP in the hard MTU calculations net/mlx5e: Do not update BQL of old txqs during channel reconfiguration net/mlx5e: Trigger neighbor resolution for unresolved destinations net/mlx5e: Use ip6_dst_lookup instead of ipv6_dst_lookup_flow for MAC init net/mlx5: Serialize firmware reset with devlink net/mlx5: fw_tracer, Handle escaped percent properly net/mlx5: fw_tracer, Validate format string parameters net/mlx5: Drain firmware reset in shutdown callback net/mlx5: fw reset, clear reset requested on drain_fw_reset net: dsa: mxl-gsw1xx: manually clear RANEG bit net: dsa: mxl-gsw1xx: fix .shutdown driver operation ...
2025-12-18net: hns3: add VLAN id validation before usingJian Shen
Currently, the VLAN id may be used without validation when receive a VLAN configuration mailbox from VF. The length of vlan_del_fail_bmap is BITS_TO_LONGS(VLAN_N_VID). It may cause out-of-bounds memory access once the VLAN id is bigger than or equal to VLAN_N_VID. Therefore, VLAN id needs to be checked to ensure it is within the range of VLAN_N_VID. Fixes: fe4144d47eef ("net: hns3: sync VLAN filter entries when kill VLAN ID failed") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20251211023737.2327018-4-shaojijie@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net: hns3: using the num_tqps to check whether tqp_index is out of range ↵Jian Shen
when vf get ring info from mbx Currently, rss_size = num_tqps / tc_num. If tc_num is 1, then num_tqps equals rss_size. However, if the tc_num is greater than 1, then rss_size will be less than num_tqps, causing the tqp_index check for subsequent TCs using rss_size to always fail. This patch uses the num_tqps to check whether tqp_index is out of range, instead of rss_size. Fixes: 326334aad024 ("net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20251211023737.2327018-3-shaojijie@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net: hns3: using the num_tqps in the vf driver to apply for resourcesJian Shen
Currently, hdev->htqp is allocated using hdev->num_tqps, and kinfo->tqp is allocated using kinfo->num_tqps. However, kinfo->num_tqps is set to min(new_tqps, hdev->num_tqps); Therefore, kinfo->num_tqps may be smaller than hdev->num_tqps, which causes some hdev->htqp[i] to remain uninitialized in hclgevf_knic_setup(). Thus, this patch allocates hdev->htqp and kinfo->tqp using hdev->num_tqps, ensuring that the lengths of hdev->htqp and kinfo->tqp are consistent and that all elements are properly initialized. Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20251211023737.2327018-2-shaojijie@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net: enetc: do not transmit redirected XDP frames when the link is downWei Fang
In the current implementation, the enetc_xdp_xmit() always transmits redirected XDP frames even if the link is down, but the frames cannot be transmitted from TX BD rings when the link is down, so the frames are still kept in the TX BD rings. If the XDP program is uninstalled, users will see the following warning logs. fsl_enetc 0000:00:00.0 eno0: timeout for tx ring #6 clear More worse, the TX BD ring cannot work properly anymore, because the HW PIR and CIR are not equal after the re-initialization of the TX BD ring. At this point, the BDs between CIR and PIR are invalid, which will cause a hardware malfunction. Another reason is that there is internal context in the ring prefetch logic that will retain the state from the first incarnation of the ring and continue prefetching from the stale location when we re-initialize the ring. The internal context is only reset by an FLR. That is to say, for LS1028A ENETC, software cannot set the HW CIR and PIR when initializing the TX BD ring. It does not make sense to transmit redirected XDP frames when the link is down. Add a link status check to prevent transmission in this condition. This fixes part of the issue, but more complex cases remain. For example, the TX BD ring may still contain unsent frames when the link goes down. Those situations require additional patches, which will build on this one. Fixes: 9d2b68cc108d ("net: enetc: add support for XDP_REDIRECT") Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Hariprasad Kelam <hkelam@marvell.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20251211020919.121113-1-wei.fang@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5e: Don't include PSP in the hard MTU calculationsCosmin Ratiu
Commit [1] added the 40 bytes required by the PSP header+trailer and the UDP header to MLX5E_ETH_HARD_MTU, which limits the device-wide max software MTU that could be set. This is not okay, because most packets are not PSP packets and it doesn't make sense to always reserve space for headers which won't get added in most cases. As it turns out, for TCP connections, PSP overhead is already taken into account in the TCP MSS calculations via inet_csk(sk)->icsk_ext_hdr_len. This was added in commit [2]. This means that the extra space reserved in the hard MTU for mlx5 ends up unused and wasted. Remove the unnecessary 40 byte reservation from hard MTU. [1] commit e5a1861a298e ("net/mlx5e: Implement PSP Tx data path") [2] commit e97269257fe4 ("net: psp: update the TCP MSS to reflect PSP packet overhead") Fixes: e5a1861a298e ("net/mlx5e: Implement PSP Tx data path") Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-10-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5e: Do not update BQL of old txqs during channel reconfigurationTariq Toukan
During channel reconfiguration (e.g., ethtool private flags changes), the driver can trigger a kernel BUG_ON in dql_completed() with the error "kernel BUG at lib/dynamic_queue_limits.c:99". The issue occurs in the following sequence: During mlx5e_safe_switch_params(), old channels are deactivated via mlx5e_deactivate_txqsq(). New channels are created and activated, taking ownership of the netdev_queues and their BQL state. When old channels are closed via mlx5e_close_txqsq(), there may be pending TX descriptors (sq->cc != sq->pc) that were in-flight during the deactivation. mlx5e_free_txqsq_descs() frees these pending descriptors and attempts to complete them via netdev_tx_completed_queue(). However, the BQL state (dql->num_queued and dql->num_completed) have been reset in mlx5e_activate_txqsq and belong to the new queue owner, leading to dql->num_queued - dql->num_completed < nbytes. This triggers BUG_ON(count > num_queued - num_completed) in dql_completed(). Fixes: 3b88a535a8e1 ("net/mlx5e: Defer channels closure to reduce interface down time") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: William Tu <witu@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-9-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5e: Trigger neighbor resolution for unresolved destinationsJianbo Liu
When initializing the MAC addresses for an outbound IPsec packet offload rule in mlx5e_ipsec_init_macs, the call to dst_neigh_lookup is used to find the next-hop neighbor (typically the gateway in tunnel mode). This call might create a new neighbor entry if one doesn't already exist. This newly created entry starts in the INCOMPLETE state, as the kernel hasn't yet sent an ARP or NDISC probe to resolve the MAC address. In this case, neigh_ha_snapshot will correctly return an all-zero MAC address. IPsec packet offload requires the actual next-hop MAC address to program the rule correctly. If the neighbor state is INCOMPLETE when the rule is created, the hardware rule is programmed with an all-zero destination MAC address. Packets sent using this rule will be subsequently dropped by the receiving network infrastructure or host. This patch adds a check specifically for the outbound offload path. If neigh_ha_snapshot returns an all-zero MAC address, it proactively calls neigh_event_send(n, NULL). This ensures the kernel immediately sends the initial ARP or NDISC probe if one isn't already pending, accelerating the resolution process. This helps prevent the hardware rule from being programmed with an invalid MAC address and avoids packet drops due to unresolved neighbors. Fixes: 71670f766b8f ("net/mlx5e: Support routed networks during IPsec MACs initialization") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-8-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5e: Use ip6_dst_lookup instead of ipv6_dst_lookup_flow for MAC initJianbo Liu
Replace ipv6_stub->ipv6_dst_lookup_flow() with ip6_dst_lookup() in mlx5e_ipsec_init_macs() since IPsec transformations are not needed during Security Association setup - only basic routing information is required for nexthop MAC address resolution. This resolves an issue where XfrmOutNoStates error counter would be incremented when xfrm policy is configured before xfrm state, as the IPsec-aware routing function would attempt policy checks during SA initialization. Fixes: 71670f766b8f ("net/mlx5e: Support routed networks during IPsec MACs initialization") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-7-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5: Serialize firmware reset with devlinkShay Drory
The firmware reset mechanism can be triggered by asynchronous events, which may race with other devlink operations like devlink reload or devlink dev eswitch set, potentially leading to inconsistent states. This patch addresses the race by using the devl_lock to serialize the firmware reset against other devlink operations. When a reset is requested, the driver attempts to acquire the lock. If successful, it sets a flag to block devlink reload or eswitch changes, ACKs the reset to firmware and then releases the lock. If the lock is already held by another operation, the driver NACKs the firmware reset request, indicating that the reset cannot proceed. Firmware reset does not keep the devl_lock and instead uses an internal firmware reset bit. This is because firmware resets can be triggered by asynchronous events, and processed in different threads. It is illegal and unsafe to acquire a lock in one thread and attempt to release it in another, as lock ownership is intrinsically thread-specific. This change ensures that firmware resets and other devlink operations are mutually exclusive during the critical reset request phase, preventing race conditions. Fixes: 38b9f903f22b ("net/mlx5: Handle sync reset request event") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Mateusz Berezecki <mberezecki@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-6-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5: fw_tracer, Handle escaped percent properlyShay Drory
The firmware tracer's format string validation and parameter counting did not properly handle escaped percent signs (%%). This caused fw_tracer to count more parameters when trace format strings contained literal percent characters. To fix it, allow %% to pass string validation and skip %% sequences when counting parameters since they represent literal percent signs rather than format specifiers. Fixes: 70dd6fdb8987 ("net/mlx5: FW tracer, parse traces and kernel tracing support") Signed-off-by: Shay Drory <shayd@nvidia.com> Reported-by: Breno Leitao <leitao@debian.org> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/ Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-5-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5: fw_tracer, Validate format string parametersShay Drory
Add validation for format string parameters in the firmware tracer to prevent potential security vulnerabilities and crashes from malformed format strings received from firmware. The firmware tracer receives format strings from the device firmware and uses them to format trace messages. Without proper validation, bad firmware could provide format strings with invalid format specifiers (e.g., %s, %p, %n) that could lead to crashes, or other undefined behavior. Add mlx5_tracer_validate_params() to validate that all format specifiers in trace strings are limited to safe integer/hex formats (%x, %d, %i, %u, %llx, %lx, etc.). Reject strings containing other format types that could be used to access arbitrary memory or cause crashes. Invalid format strings are added to the trace output for visibility with "BAD_FORMAT: " prefix. Fixes: 70dd6fdb8987 ("net/mlx5: FW tracer, parse traces and kernel tracing support") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reported-by: Breno Leitao <leitao@debian.org> Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/ Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-4-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5: Drain firmware reset in shutdown callbackMoshe Shemesh
Invoke drain_fw_reset() in the shutdown callback to ensure all firmware reset handling is completed before shutdown proceeds. Fixes: 16d42d313350 ("net/mlx5: Drain fw_reset when removing device") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Shay Drori <shayd@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-3-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-18net/mlx5: fw reset, clear reset requested on drain_fw_resetMoshe Shemesh
drain_fw_reset() waits for ongoing firmware reset events and blocks new event handling, but does not clear the reset requested flag, and may keep sync reset polling. To fix it, call mlx5_sync_reset_clear_reset_requested() to clear the flag, stop sync reset polling, and resume health polling, ensuring health issues are still detected after the firmware reset drain. Fixes: 16d42d313350 ("net/mlx5: Drain fw_reset when removing device") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Shay Drori <shayd@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1765284977-1363052-2-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-17e1000: fix OOB in e1000_tbi_should_accept()Guangshuo Li
In e1000_tbi_should_accept() we read the last byte of the frame via 'data[length - 1]' to evaluate the TBI workaround. If the descriptor- reported length is zero or larger than the actual RX buffer size, this read goes out of bounds and can hit unrelated slab objects. The issue is observed from the NAPI receive path (e1000_clean_rx_irq): ================================================================== BUG: KASAN: slab-out-of-bounds in e1000_tbi_should_accept+0x610/0x790 Read of size 1 at addr ffff888014114e54 by task sshd/363 CPU: 0 PID: 363 Comm: sshd Not tainted 5.18.0-rc1 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0x5a/0x74 print_address_description+0x7b/0x440 print_report+0x101/0x200 kasan_report+0xc1/0xf0 e1000_tbi_should_accept+0x610/0x790 e1000_clean_rx_irq+0xa8c/0x1110 e1000_clean+0xde2/0x3c10 __napi_poll+0x98/0x380 net_rx_action+0x491/0xa20 __do_softirq+0x2c9/0x61d do_softirq+0xd1/0x120 </IRQ> <TASK> __local_bh_enable_ip+0xfe/0x130 ip_finish_output2+0x7d5/0xb00 __ip_queue_xmit+0xe24/0x1ab0 __tcp_transmit_skb+0x1bcb/0x3340 tcp_write_xmit+0x175d/0x6bd0 __tcp_push_pending_frames+0x7b/0x280 tcp_sendmsg_locked+0x2e4f/0x32d0 tcp_sendmsg+0x24/0x40 sock_write_iter+0x322/0x430 vfs_write+0x56c/0xa60 ksys_write+0xd1/0x190 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f511b476b10 Code: 73 01 c3 48 8b 0d 88 d3 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d f9 2b 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 8e 9b 01 00 48 89 04 24 RSP: 002b:00007ffc9211d4e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000004024 RCX: 00007f511b476b10 RDX: 0000000000004024 RSI: 0000559a9385962c RDI: 0000000000000003 RBP: 0000559a9383a400 R08: fffffffffffffff0 R09: 0000000000004f00 R10: 0000000000000070 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffc9211d57f R14: 0000559a9347bde7 R15: 0000000000000003 </TASK> Allocated by task 1: __kasan_krealloc+0x131/0x1c0 krealloc+0x90/0xc0 add_sysfs_param+0xcb/0x8a0 kernel_add_sysfs_param+0x81/0xd4 param_sysfs_builtin+0x138/0x1a6 param_sysfs_init+0x57/0x5b do_one_initcall+0x104/0x250 do_initcall_level+0x102/0x132 do_initcalls+0x46/0x74 kernel_init_freeable+0x28f/0x393 kernel_init+0x14/0x1a0 ret_from_fork+0x22/0x30 The buggy address belongs to the object at ffff888014114000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1620 bytes to the right of 2048-byte region [ffff888014114000, ffff888014114800] The buggy address belongs to the physical page: page:ffffea0000504400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14110 head:ffffea0000504400 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x100000000010200(slab|head|node=0|zone=1) raw: 0100000000010200 0000000000000000 dead000000000001 ffff888013442000 raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected ================================================================== This happens because the TBI check unconditionally dereferences the last byte without validating the reported length first: u8 last_byte = *(data + length - 1); Fix by rejecting the frame early if the length is zero, or if it exceeds adapter->rx_buffer_len. This preserves the TBI workaround semantics for valid frames and prevents touching memory beyond the RX buffer. Fixes: 2037110c96d5 ("e1000: move tbi workaround code into helper function") Cc: stable@vger.kernel.org Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-12-17idpf: reduce mbx_task schedule delay to 300usBrian Vazquez
During the IDPF init phase, the mailbox runs in poll mode until it is configured to properly handle interrupts. The previous delay of 300ms is excessively long for the mailbox polling mechanism, which causes a slow initialization of ~2s: echo 0000:06:12.4 > /sys/bus/pci/drivers/idpf/bind [ 52.444239] idpf 0000:06:12.4: enabling device (0000 -> 0002) [ 52.485005] idpf 0000:06:12.4: Device HW Reset initiated [ 54.177181] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP [ 54.206177] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default [ 54.206182] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default Changing the delay to 300us avoids the delays during the initial mailbox transactions, making the init phase much faster: [ 83.342590] idpf 0000:06:12.4: enabling device (0000 -> 0002) [ 83.384402] idpf 0000:06:12.4: Device HW Reset initiated [ 83.518323] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP [ 83.547430] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default [ 83.547435] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default Fixes: 4930fbf419a7 ("idpf: add core init and interrupt request") Signed-off-by: Brian Vazquez <brianvv@google.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Samuel Salin <Samuel.salin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-12-17idpf: fix LAN memory regions command on some NVMsLarysa Zaremba
IPU SDK versions 1.9 through 2.0.5 require send buffer to contain a single empty memory region. Set number of regions to 1 and use appropriate send buffer size to satisfy this requirement. Fixes: 6aa53e861c1a ("idpf: implement get LAN MMIO memory regions") Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-12-17iavf: fix off-by-one issues in iavf_config_rss_reg()Kohei Enju
There are off-by-one bugs when configuring RSS hash key and lookup table, causing out-of-bounds reads to memory [1] and out-of-bounds writes to device registers. Before commit 43a3d9ba34c9 ("i40evf: Allow PF driver to configure RSS"), the loop upper bounds were: i <= I40E_VFQF_{HKEY,HLUT}_MAX_INDEX which is safe since the value is the last valid index. That commit changed the bounds to: i <= adapter->rss_{key,lut}_size / 4 where `rss_{key,lut}_size / 4` is the number of dwords, so the last valid index is `(rss_{key,lut}_size / 4) - 1`. Therefore, using `<=` accesses one element past the end. Fix the issues by using `<` instead of `<=`, ensuring we do not exceed the bounds. [1] KASAN splat about rss_key_size off-by-one BUG: KASAN: slab-out-of-bounds in iavf_config_rss+0x619/0x800 Read of size 4 at addr ffff888102c50134 by task kworker/u8:6/63 CPU: 0 UID: 0 PID: 63 Comm: kworker/u8:6 Not tainted 6.18.0-rc2-enjuk-tnguy-00378-g3005f5b77652-dirty #156 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: iavf iavf_watchdog_task Call Trace: <TASK> dump_stack_lvl+0x6f/0xb0 print_report+0x170/0x4f3 kasan_report+0xe1/0x1a0 iavf_config_rss+0x619/0x800 iavf_watchdog_task+0x2be7/0x3230 process_one_work+0x7fd/0x1420 worker_thread+0x4d1/0xd40 kthread+0x344/0x660 ret_from_fork+0x249/0x320 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 63: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x7f/0x90 __kmalloc_noprof+0x246/0x6f0 iavf_watchdog_task+0x28fc/0x3230 process_one_work+0x7fd/0x1420 worker_thread+0x4d1/0xd40 kthread+0x344/0x660 ret_from_fork+0x249/0x320 ret_from_fork_asm+0x1a/0x30 The buggy address belongs to the object at ffff888102c50100 which belongs to the cache kmalloc-64 of size 64 The buggy address is located 0 bytes to the right of allocated 52-byte region [ffff888102c50100, ffff888102c50134) The buggy address belongs to the physical page: page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x102c50 flags: 0x200000000000000(node=0|zone=2) page_type: f5(slab) raw: 0200000000000000 ffff8881000418c0 dead000000000122 0000000000000000 raw: 0000000000000000 0000000080200020 00000000f5000000 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888102c50000: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc ffff888102c50080: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc >ffff888102c50100: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc ^ ffff888102c50180: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc ffff888102c50200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc Fixes: 43a3d9ba34c9 ("i40evf: Allow PF driver to configure RSS") Signed-off-by: Kohei Enju <enjuk@amazon.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-12-17i40e: validate ring_len parameter against hardware-specific valuesGregory Herrero
The maximum number of descriptors supported by the hardware is hardware-dependent and can be retrieved using i40e_get_max_num_descriptors(). Move this function to a shared header and use it when checking for valid ring_len parameter rather than using hardcoded value. By fixing an over-acceptance issue, behavior change could be seen where ring_len could now be rejected while configuring rx and tx queues if its size is larger than the hardware-dependent maximum number of descriptors. Fixes: 55d225670def ("i40e: add validation for ring_len param") Signed-off-by: Gregory Herrero <gregory.herrero@oracle.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-12-17i40e: fix scheduling in set_rx_modePrzemyslaw Korba
Add service task schedule to set_rx_mode. In some cases there are error messages printed out in PTP application (ptp4l): ptp4l[13848.762]: port 1 (ens2f3np3): received SYNC without timestamp ptp4l[13848.825]: port 1 (ens2f3np3): received SYNC without timestamp ptp4l[13848.887]: port 1 (ens2f3np3): received SYNC without timestamp This happens when service task would not run immediately after set_rx_mode, and we need it for setup tasks. This service task checks, if PTP RX packets are hung in firmware, and propagate correct settings such as multicast address for IEEE 1588 Precision Time Protocol. RX timestamping depends on some of these filters set. Bug happens only with high PTP packets frequency incoming, and not every run since sometimes service task is being ran from a different place immediately after starting ptp4l. Fixes: 0e4425ed641f ("i40e: fix: do not sleep in netdev_ops") Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-12-10broadcom: b44: prevent uninitialized value usageAlexey Simakov
On execution path with raised B44_FLAG_EXTERNAL_PHY, b44_readphy() leaves bmcr value uninitialized and it is used later in the code. Add check of this flag at the beginning of the b44_nway_reset() and exit early of the function with restarting autonegotiation if an external PHY is used. Fixes: 753f492093da ("[B44]: port to native ssb support") Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexey Simakov <bigalex934@gmail.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20251205155815.4348-1-bigalex934@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-10net: ti: icssg-prueth: add PTP_1588_CLOCK_OPTIONAL dependencyArnd Bergmann
The new icssg-prueth driver needs the same dependency as the other parts that use the ptp-1588: WARNING: unmet direct dependencies detected for TI_ICSS_IEP Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PTP_1588_CLOCK_OPTIONAL [=m] && TI_PRUSS [=y] Selected by [y]: - TI_PRUETH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PRU_REMOTEPROC [=y] && NET_SWITCHDEV [=y] Add the correct dependency on the two drivers missing it, and remove the pointless 'imply' in the process. Fixes: e654b85a693e ("net: ti: icssg-prueth: Add ICSSG Ethernet driver for AM65x SR1.0 platforms") Fixes: 511f6c1ae093 ("net: ti: icssm-prueth: Adds ICSSM Ethernet driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20251204100138.1034175-1-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-04Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdmaLinus Torvalds
Pull rdma updates from Jason Gunthorpe: "This has another new RDMA driver 'bng_en' for latest generation Broadcom NICs. There might be one more new driver still to come. Otherwise it is a fairly quite cycle. Summary: - Minor driver bug fixes and updates to cxgb4, rxe, rdmavt, bnxt_re, mlx5 - Many bug fix patches for irdma - WQ_PERCPU annotations and system_dfl_wq changes - Improved mlx5 support for "other eswitches" and multiple PFs - 1600Gbps link speed reporting support. Four Digits Now! - New driver bng_en for latest generation Broadcom NICs - Bonding support for hns - Adjust mlx5's hmm based ODP to work with the very large address space created by the new 5 level paging default on x86 - Lockdep fixups in rxe and siw" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (65 commits) RDMA/rxe: reclassify sockets in order to avoid false positives from lockdep RDMA/siw: reclassify sockets in order to avoid false positives from lockdep RDMA/bng_re: Remove prefetch instruction RDMA/core: Reduce cond_resched() frequency in __ib_umem_release RDMA/irdma: Fix SRQ shadow area address initialization RDMA/irdma: Remove doorbell elision logic RDMA/irdma: Do not set IBK_LOCAL_DMA_LKEY for GEN3+ RDMA/irdma: Do not directly rely on IB_PD_UNSAFE_GLOBAL_RKEY RDMA/irdma: Add missing mutex destroy RDMA/irdma: Fix SIGBUS in AEQ destroy RDMA/irdma: Add a missing kfree of struct irdma_pci_f for GEN2 RDMA/irdma: Fix data race in irdma_free_pble RDMA/irdma: Fix data race in irdma_sc_ccq_arm RDMA/mlx5: Add support for 1600_8x lane speed RDMA/core: Add new IB rate for XDR (8x) support IB/mlx5: Reduce IMR KSM size when 5-level paging is enabled RDMA/bnxt_re: Pass correct flag for dma mr creation RDMA/bnxt_re: Fix the inline size for GenP7 devices RDMA/hns: Support reset recovery for bond RDMA/hns: Support link state reporting for bond ...
2025-12-04bnxt_en: Fix XDP_TX pathMichael Chan
For XDP_TX action in bnxt_rx_xdp(), clearing of the event flags is not correct. __bnxt_poll_work() -> bnxt_rx_pkt() -> bnxt_rx_xdp() may be looping within NAPI and some event flags may be set in earlier iterations. In particular, if BNXT_TX_EVENT is set earlier indicating some XDP_TX packets are ready and pending, it will be cleared if it is XDP_TX action again. Normally, we will set BNXT_TX_EVENT again when we successfully call __bnxt_xmit_xdp(). But if the TX ring has no more room, the flag will not be set. This will cause the TX producer to be ahead but the driver will not hit the TX doorbell. For multi-buf XDP_TX, there is no need to clear the event flags and set BNXT_AGG_EVENT. The BNXT_AGG_EVENT flag should have been set earlier in bnxt_rx_pkt(). The visible symptom of this is that the RX ring associated with the TX XDP ring will eventually become empty and all packets will be dropped. Because this condition will cause the driver to not refill the RX ring seeing that the TX ring has forever pending XDP_TX packets. The fix is to only clear BNXT_RX_EVENT when we have successfully called __bnxt_xmit_xdp(). Fixes: 7f0a168b0441 ("bnxt_en: Add completion ring pointer in TX and RX ring structures") Reported-by: Pavel Dubovitsky <pdubovitsky@meta.com> Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20251203003024.2246699-1-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-04gve: Move gve_init_clock to after AQ CONFIGURE_DEVICE_RESOURCES callTim Hostetler
commit 46e7860ef941 ("gve: Move ptp_schedule_worker to gve_init_clock") moved the first invocation of the AQ command REPORT_NIC_TIMESTAMP to gve_probe(). However, gve_init_clock() invoking REPORT_NIC_TIMESTAMP is not valid until after gve_probe() invokes the AQ command CONFIGURE_DEVICE_RESOURCES. Failure to do so results in the following error: gve 0000:00:07.0: failed to read NIC clock -11 This was missed earlier because the driver under test was loaded at runtime instead of boot-time. The boot-time driver had already initialized the device, causing the runtime driver to successfully call gve_init_clock() incorrectly. Fixes: 46e7860ef941 ("gve: Move ptp_schedule_worker to gve_init_clock") Reviewed-by: Ankit Garg <nktgrg@google.com> Signed-off-by: Tim Hostetler <thostet@google.com> Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20251202200207.1434749-1-hramamurthy@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-04r8169: fix RTL8117 Wake-on-Lan in DASH modeRené Rebe
Wake-on-Lan does currently not work for r8169 in DASH mode, e.g. the ASUS Pro WS X570-ACE with RTL8168fp/RTL8117. Fix by not returning early in rtl_prepare_power_down when dash_enabled. While this fixes WoL, it still kills the OOB RTL8117 remote management BMC connection. Fix by not calling rtl8168_driver_stop if WoL is enabled. Fixes: 065c27c184d6 ("r8169: phy power ops") Signed-off-by: René Rebe <rene@exactco.de> Cc: stable@vger.kernel.org Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://patch.msgid.link/20251202.194137.1647877804487085954.rene@exactco.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-04mlxsw: spectrum_mr: Fix use-after-free when updating multicast route statsIdo Schimmel
Cited commit added a dedicated mutex (instead of RTNL) to protect the multicast route list, so that it will not change while the driver periodically traverses it in order to update the kernel about multicast route stats that were queried from the device. One instance of list entry deletion (during route replace) was missed and it can result in a use-after-free [1]. Fix by acquiring the mutex before deleting the entry from the list and releasing it afterwards. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum] Read of size 8 at addr ffff8881523c2fa8 by task kworker/2:5/22043 CPU: 2 UID: 0 PID: 22043 Comm: kworker/2:5 Not tainted 6.18.0-rc1-custom-g1a3d6d7cd014 #1 PREEMPT(full) Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017 Workqueue: mlxsw_core mlxsw_sp_mr_stats_update [mlxsw_spectrum] Call Trace: <TASK> dump_stack_lvl+0xba/0x110 print_report+0x174/0x4f5 kasan_report+0xdf/0x110 mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum] process_one_work+0x9cc/0x18e0 worker_thread+0x5df/0xe40 kthread+0x3b8/0x730 ret_from_fork+0x3e9/0x560 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 29933: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x8f/0xa0 mlxsw_sp_mr_route_add+0xd8/0x4770 [mlxsw_spectrum] mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum] process_one_work+0x9cc/0x18e0 worker_thread+0x5df/0xe40 kthread+0x3b8/0x730 ret_from_fork+0x3e9/0x560 ret_from_fork_asm+0x1a/0x30 Freed by task 29933: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_save_free_info+0x3b/0x70 __kasan_slab_free+0x43/0x70 kfree+0x14e/0x700 mlxsw_sp_mr_route_add+0x2dea/0x4770 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:444 [mlxsw_spectrum] mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum] process_one_work+0x9cc/0x18e0 worker_thread+0x5df/0xe40 kthread+0x3b8/0x730 ret_from_fork+0x3e9/0x560 ret_from_fork_asm+0x1a/0x30 Fixes: f38656d06725 ("mlxsw: spectrum_mr: Protect multicast route list with a lock") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/f996feecfd59fde297964bfc85040b6d83ec6089.1764695650.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-04mlxsw: spectrum_router: Fix neighbour use-after-freeIdo Schimmel
We sometimes observe use-after-free when dereferencing a neighbour [1]. The problem seems to be that the driver stores a pointer to the neighbour, but without holding a reference on it. A reference is only taken when the neighbour is used by a nexthop. Fix by simplifying the reference counting scheme. Always take a reference when storing a neighbour pointer in a neighbour entry. Avoid taking a referencing when the neighbour is used by a nexthop as the neighbour entry associated with the nexthop already holds a reference. Tested by running the test that uncovered the problem over 300 times. Without this patch the problem was reproduced after a handful of iterations. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x2d4/0x310 Read of size 8 at addr ffff88817f8e3420 by task ip/3929 CPU: 3 UID: 0 PID: 3929 Comm: ip Not tainted 6.18.0-rc4-virtme-g36b21a067510 #3 PREEMPT(full) Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023 Call Trace: <TASK> dump_stack_lvl+0x6f/0xa0 print_address_description.constprop.0+0x6e/0x300 print_report+0xfc/0x1fb kasan_report+0xe4/0x110 mlxsw_sp_neigh_entry_update+0x2d4/0x310 mlxsw_sp_router_rif_gone_sync+0x35f/0x510 mlxsw_sp_rif_destroy+0x1ea/0x730 mlxsw_sp_inetaddr_port_vlan_event+0xa1/0x1b0 __mlxsw_sp_inetaddr_lag_event+0xcc/0x130 __mlxsw_sp_inetaddr_event+0xf5/0x3c0 mlxsw_sp_router_netdevice_event+0x1015/0x1580 notifier_call_chain+0xcc/0x150 call_netdevice_notifiers_info+0x7e/0x100 __netdev_upper_dev_unlink+0x10b/0x210 netdev_upper_dev_unlink+0x79/0xa0 vrf_del_slave+0x18/0x50 do_set_master+0x146/0x7d0 do_setlink.isra.0+0x9a0/0x2880 rtnl_newlink+0x637/0xb20 rtnetlink_rcv_msg+0x6fe/0xb90 netlink_rcv_skb+0x123/0x380 netlink_unicast+0x4a3/0x770 netlink_sendmsg+0x75b/0xc90 __sock_sendmsg+0xbe/0x160 ____sys_sendmsg+0x5b2/0x7d0 ___sys_sendmsg+0xfd/0x180 __sys_sendmsg+0x124/0x1c0 do_syscall_64+0xbb/0xfd0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 [...] Allocated by task 109: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x7b/0x90 __kmalloc_noprof+0x2c1/0x790 neigh_alloc+0x6af/0x8f0 ___neigh_create+0x63/0xe90 mlxsw_sp_nexthop_neigh_init+0x430/0x7e0 mlxsw_sp_nexthop_type_init+0x212/0x960 mlxsw_sp_nexthop6_group_info_init.constprop.0+0x81f/0x1280 mlxsw_sp_nexthop6_group_get+0x392/0x6a0 mlxsw_sp_fib6_entry_create+0x46a/0xfd0 mlxsw_sp_router_fib6_replace+0x1ed/0x5f0 mlxsw_sp_router_fib6_event_work+0x10a/0x2a0 process_one_work+0xd57/0x1390 worker_thread+0x4d6/0xd40 kthread+0x355/0x5b0 ret_from_fork+0x1d4/0x270 ret_from_fork_asm+0x11/0x20 Freed by task 154: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x43/0x70 kmem_cache_free_bulk.part.0+0x1eb/0x5e0 kvfree_rcu_bulk+0x1f2/0x260 kfree_rcu_work+0x130/0x1b0 process_one_work+0xd57/0x1390 worker_thread+0x4d6/0xd40 kthread+0x355/0x5b0 ret_from_fork+0x1d4/0x270 ret_from_fork_asm+0x11/0x20 Last potentially related work creation: kasan_save_stack+0x30/0x50 kasan_record_aux_stack+0x8c/0xa0 kvfree_call_rcu+0x93/0x5b0 mlxsw_sp_router_neigh_event_work+0x67d/0x860 process_one_work+0xd57/0x1390 worker_thread+0x4d6/0xd40 kthread+0x355/0x5b0 ret_from_fork+0x1d4/0x270 ret_from_fork_asm+0x11/0x20 Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/92d75e21d95d163a41b5cea67a15cd33f547cba6.1764695650.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-04mlxsw: spectrum_router: Fix possible neighbour reference count leakIdo Schimmel
mlxsw_sp_router_schedule_work() takes a reference on a neighbour, expecting a work item to release it later on. However, we might fail to schedule the work item, in which case the neighbour reference count will be leaked. Fix by taking the reference just before scheduling the work item. Note that mlxsw_sp_router_schedule_work() can receive a NULL neighbour pointer, but neigh_clone() handles that correctly. Spotted during code review, did not actually observe the reference count leak. Fixes: 151b89f6025a ("mlxsw: spectrum_router: Reuse work neighbor initialization in work scheduler") Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/ec2934ae4aca187a8d8c9329a08ce93cca411378.1764695650.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-12-04Merge tag 'pci-v6.19-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan Williams) - Switch vmd from custom domain number allocator to the common allocator to prevent a potential race with new non-VMD buses (Dan Williams) - Enable Precision Time Measurement (PTM) only if device advertises support for a relevant role, to prevent invalid PTM Requests that cause ACS violations that are reported as AER Uncorrectable Non-Fatal errors (Mika Westerberg) Resource management: - Prevent resource tree corruption when BAR resize fails (Ilpo Järvinen) - Restore BARs to the original size if a BAR resize fails (Ilpo Järvinen) - Remove BAR release from BAR resize attempts by the xe, i915, and amdgpu drivers so the PCI core can restore BARs if the resize fails (Ilpo Järvinen) - Move Resizable BAR code to rebar.c (Ilpo Järvinen) - Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo Järvinen) - Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo Järvinen) Power management and error handling: - For drivers using PCI legacy suspend, save config state at suspend so that state (not any earlier state from enumeration, probe, or error recovery) will be restored when resuming (Lukas Wunner) - For devices with no driver or a driver that lacks power management, save config state at hibernate so that state (not any earlier state from enumeration, probe, or error recovery) will be restored when resuming (Lukas Wunner) - Save device config space on device addition, before driver binding, so error recovery works more reliably (Lukas Wunner) - Drop pci_save_state() from several drivers that no longer need it since the PCI core always does it and pci_restore_state() no longer invalidates the saved state (Lukas Wunner) - Document use of pci_save_state() by drivers to capture the state they want restored during error recovery (Lukas Wunner) Power control: - Add a struct pci_ops.assert_perst() function pointer to assert/deassert PCIe PERST# and implement it for the qcom driver (Krishna Chaitanya Chundru) - Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe switch, which must be held in reset after poweron so the pwrctrl driver can configure the switch via I2C before bringing up the links (Krishna Chaitanya Chundru) Endpoint framework: - Convert the endpoint doorbell test to use a threaded IRQ to fix a 'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri) - Add endpoint VNTB MSI doorbell support to reduce latency between host and endpoint (Frank Li) New native PCIe controller drivers: - Add CIX Sky1 host controller DT binding and driver (Hans Zhang) - Add NXP S32G host controller DT binding and driver (Vincent Guittot) - Add Renesas RZ/G3S host controller DT binding and driver (Claudiu Beznea) - Add SpacemiT K1 host controller DT binding and driver (Alex Elder) Amlogic Meson PCIe controller driver: - Update DT binding to name DBI region 'dbi', not 'elbi', and update driver to support both (Manivannan Sadhasivam) Apple PCIe controller driver: - Move struct pci_host_bridge allocation from pci_host_common_init() to callers, which significantly simplifies pcie-apple (Marc Zyngier) Broadcom STB PCIe controller driver: - Disable advertising ASPM L0s support correctly (Jim Quinlan) - Add a panic/die handler to print diagnostic info in case PCIe caused an unrecoverable abort (Jim Quinlan) Cadence PCIe controller driver: - Add module support for Cadence platform host and endpoint controller driver (Manikandan K Pillai) - Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare for new CIX Sky1 driver (Manikandan K Pillai) MediaTek PCIe controller driver: - Convert DT binding to YAML schema (Christian Marangi) - Add Airoha AN7583 DT compatible and driver support (Christian Marangi) Qualcomm PCIe controller driver: - Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu) - Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280, sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT schemas (Krzysztof Kozlowski) - Look up OPP using both frequency and data rate (not just frequency) so RPMh votes can account for both (Krishna Chaitanya Chundru) Rockchip DesignWare PCIe controller driver: - Add Rockchip RK3528 compatible strings in DT binding (Yao Zi) STMicroelectronics STM32MP25 PCIe controller driver: - Fix a race between link training and endpoint register initialization (Christian Bruel) - Align endpoint allocations to match the ATU requirements (Christian Bruel) Synopsys DesignWare PCIe controller driver: - Clear L1 PM Substate Capability 'Supported' bits unless glue driver says it's supported, which prevents users from enabling non-working L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas) - Remove now-superfluous L1SS disable code from tegra194 (Bjorn Helgaas) - Configure L1SS support in dw-rockchip when DT says 'supports-clkreq' (Shawn Lin) TI Keystone PCIe controller driver: - Fail the probe instead of silently succeeding if ks_pcie_of_data didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli) - Make keystone buildable as a loadable module, except on ARM32 where hook_fault_code() is __init (Siddharth Vadapalli)" * tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits) MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer PCI: sky1: Add PCIe host support for CIX Sky1 dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings PCI: cadence: Add support for High Perf Architecture (HPA) controller MAINTAINERS: Add NXP S32G PCIe controller driver maintainer PCI: s32g: Add NXP S32G PCIe controller driver (RC) PCI: dwc: Add register and bitfield definitions dt-bindings: PCI: s32g: Add NXP S32G PCIe controller PCI: Add Renesas RZ/G3S host controller driver PCI: host-generic: Move bridge allocation outside of pci_host_common_init() dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding PCI: Validate pci_rebar_size_supported() input Documentation: PCI: Amend error recovery doc with pci_save_state() rules treewide: Drop pci_save_state() after pci_restore_state() PCI/ERR: Ensure error recoverability at all times PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths PCI: dw-rockchip: Configure L1SS support PCI: tegra194: Remove unnecessary L1SS disable code ...
2025-12-04net/mlx5: Fix double unregister of HCA_PORTS componentGerd Bayer
Clear hca_devcom_comp in device's private data after unregistering it in LAG teardown. Otherwise a slightly lagging second pass through mlx5_unload_one() might try to unregister it again and trip over use-after-free. On s390 almost all PCI level recovery events trigger two passes through mxl5_unload_one() - one through the poll_health() method and one through mlx5_pci_err_detected() as callback from generic PCI error recovery. While testing PCI error recovery paths with more kernel debug features enabled, this issue reproducibly led to kernel panics with the following call chain: Unable to handle kernel pointer dereference in virtual kernel address space Failing address: 6b6b6b6b6b6b6000 TEID: 6b6b6b6b6b6b6803 ESOP-2 FSI Fault in home space mode while using kernel ASCE. AS:00000000705c4007 R3:0000000000000024 Oops: 0038 ilc:3 [#1]SMP CPU: 14 UID: 0 PID: 156 Comm: kmcheck Kdump: loaded Not tainted 6.18.0-20251130.rc7.git0.16131a59cab1.300.fc43.s390x+debug #1 PREEMPT Krnl PSW : 0404e00180000000 0000020fc86aa1dc (__lock_acquire+0x5c/0x15f0) R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3 Krnl GPRS: 0000000000000000 0000020f00000001 6b6b6b6b6b6b6c33 0000000000000000 0000000000000000 0000000000000000 0000000000000001 0000000000000000 0000000000000000 0000020fca28b820 0000000000000000 0000010a1ced8100 0000010a1ced8100 0000020fc9775068 0000018fce14f8b8 0000018fce14f7f8 Krnl Code: 0000020fc86aa1cc: e3b003400004 lg %r11,832 0000020fc86aa1d2: a7840211 brc 8,0000020fc86aa5f4 *0000020fc86aa1d6: c09000df0b25 larl %r9,0000020fca28b820 >0000020fc86aa1dc: d50790002000 clc 0(8,%r9),0(%r2) 0000020fc86aa1e2: a7840209 brc 8,0000020fc86aa5f4 0000020fc86aa1e6: c0e001100401 larl %r14,0000020fca8aa9e8 0000020fc86aa1ec: c01000e25a00 larl %r1,0000020fca2f55ec 0000020fc86aa1f2: a7eb00e8 aghi %r14,232 Call Trace: __lock_acquire+0x5c/0x15f0 lock_acquire.part.0+0xf8/0x270 lock_acquire+0xb0/0x1b0 down_write+0x5a/0x250 mlx5_detach_device+0x42/0x110 [mlx5_core] mlx5_unload_one_devl_locked+0x50/0xc0 [mlx5_core] mlx5_unload_one+0x42/0x60 [mlx5_core] mlx5_pci_err_detected+0x94/0x150 [mlx5_core] zpci_event_attempt_error_recovery+0xcc/0x388 Fixes: 5a977b5833b7 ("net/mlx5: Lag, move devcom registration to LAG layer") Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Acked-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20251202-fix_lag-v1-1-59e8177ffce0@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-04net/mlx5e: Avoid unregistering PSP twiceCosmin Ratiu
PSP is unregistered twice in: _mlx5e_remove -> mlx5e_psp_unregister mlx5e_nic_cleanup -> mlx5e_psp_unregister This leads to a refcount underflow in some conditions: ------------[ cut here ]------------ refcount_t: underflow; use-after-free. WARNING: CPU: 2 PID: 1694 at lib/refcount.c:28 refcount_warn_saturate+0xd8/0xe0 [...] mlx5e_psp_unregister+0x26/0x50 [mlx5_core] mlx5e_nic_cleanup+0x26/0x90 [mlx5_core] mlx5e_remove+0xe6/0x1f0 [mlx5_core] auxiliary_bus_remove+0x18/0x30 device_release_driver_internal+0x194/0x1f0 bus_remove_device+0xc6/0x130 device_del+0x159/0x3c0 mlx5_rescan_drivers_locked+0xbc/0x2a0 [mlx5_core] [...] Do not directly remove psp from the _mlx5e_remove path, the PSP cleanup happens as part of profile cleanup. Fixes: 89ee2d92f66c ("net/mlx5e: Support PSP offload functionality") Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1764602008-1334866-3-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-04net/mlx5: make enable_mpesw idempotentMoshe Shemesh
The enable_mpesw() function returns -EINVAL if ldev->mode is not MLX5_LAG_MODE_NONE. This means attempting to enable MPESW mode when it's already enabled will fail. In contrast, disable_mpesw() properly checks if the mode is MLX5_LAG_MODE_MPESW before proceeding, making it naturally idempotent and safe to call multiple times. Fix enable_mpesw() to return success if mpesw is already enabled. Fixes: a32327a3a02c ("net/mlx5: Lag, Control MultiPort E-Switch single FDB mode") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Shay Drori <shayd@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1764602008-1334866-2-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-04net: fec: ERR007885 Workaround for XDP TX pathWei Fang
The ERR007885 will lead to a TDAR race condition for mutliQ when the driver sets TDAR and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles). And it will cause the udma_tx and udma_tx_arbiter state machines to hang. Therefore, the commit 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up") and the commit a179aad12bad ("net: fec: ERR007885 Workaround for conventional TX") have added the workaround to fix the potential issue for the conventional TX path. Similarly, the XDP TX path should also have the potential hang issue, so add the workaround for XDP TX path. Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support") Signed-off-by: Wei Fang <wei.fang@nxp.com> Link: https://patch.msgid.link/20251128025915.2486943-1-wei.fang@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-12-03Merge tag 'net-next-6.19' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "Core & protocols: - Replace busylock at the Tx queuing layer with a lockless list. Resulting in a 300% (4x) improvement on heavy TX workloads, sending twice the number of packets per second, for half the cpu cycles. - Allow constantly busy flows to migrate to a more suitable CPU/NIC queue. Normally we perform queue re-selection when flow comes out of idle, but under extreme circumstances the flows may be constantly busy. Add sysctl to allow periodic rehashing even if it'd risk packet reordering. - Optimize the NAPI skb cache, make it larger, use it in more paths. - Attempt returning Tx skbs to the originating CPU (like we already did for Rx skbs). - Various data structure layout and prefetch optimizations from Eric. - Remove ktime_get() from the recvmsg() fast path, ktime_get() is sadly quite expensive on recent AMD machines. - Extend threaded NAPI polling to allow the kthread busy poll for packets. - Make MPTCP use Rx backlog processing. This lowers the lock pressure, improving the Rx performance. - Support memcg accounting of MPTCP socket memory. - Allow admin to opt sockets out of global protocol memory accounting (using a sysctl or BPF-based policy). The global limits are a poor fit for modern container workloads, where limits are imposed using cgroups. - Improve heuristics for when to kick off AF_UNIX garbage collection. - Allow users to control TCP SACK compression, and default to 33% of RTT. - Add tcp_rcvbuf_low_rtt sysctl to let datacenter users avoid unnecessarily aggressive rcvbuf growth and overshot when the connection RTT is low. - Preserve skb metadata space across skb_push / skb_pull operations. - Support for IPIP encapsulation in the nftables flowtable offload. - Support appending IP interface information to ICMP messages (RFC 5837). - Support setting max record size in TLS (RFC 8449). - Remove taking rtnl_lock from RTM_GETNEIGHTBL and RTM_SETNEIGHTBL. - Use a dedicated lock (and RCU) in MPLS, instead of rtnl_lock. - Let users configure the number of write buffers in SMC. - Add new struct sockaddr_unsized for sockaddr of unknown length, from Kees. - Some conversions away from the crypto_ahash API, from Eric Biggers. - Some preparations for slimming down struct page. - YAML Netlink protocol spec for WireGuard. - Add a tool on top of YAML Netlink specs/lib for reporting commonly computed derived statistics and summarized system state. Driver API: - Add CAN XL support to the CAN Netlink interface. - Add uAPI for reporting PHY Mean Square Error (MSE) diagnostics, as defined by the OPEN Alliance's "Advanced diagnostic features for 100BASE-T1 automotive Ethernet PHYs" specification. - Add DPLL phase-adjust-gran pin attribute (and implement it in zl3073x). - Refactor xfrm_input lock to reduce contention when NIC offloads IPsec and performs RSS. - Add info to devlink params whether the current setting is the default or a user override. Allow resetting back to default. - Add standard device stats for PSP crypto offload. - Leverage DSA frame broadcast to implement simple HSR frame duplication for a lot of switches without dedicated HSR offload. - Add uAPI defines for 1.6Tbps link modes. Device drivers: - Add Motorcomm YT921x gigabit Ethernet switch support. - Add MUCSE driver for N500/N210 1GbE NIC series. - Convert drivers to support dedicated ops for timestamping control, and away from the direct IOCTL handling. While at it support GET operations for PHY timestamping. - Add (and convert most drivers to) a dedicated ethtool callback for reading the Rx ring count. - Significant refactoring efforts in the STMMAC driver, which supports Synopsys turn-key MAC IP integrated into a ton of SoCs. - Ethernet high-speed NICs: - Broadcom (bnxt): - support PPS in/out on all pins - Intel (100G, ice, idpf): - ice: implement standard ethtool and timestamping stats - i40e: support setting the max number of MAC addresses per VF - iavf: support RSS of GTP tunnels for 5G and LTE deployments - nVidia/Mellanox (mlx5): - reduce downtime on interface reconfiguration - disable being an XDP redirect target by default (same as other drivers) to avoid wasting resources if feature is unused - Meta (fbnic): - add support for Linux-managed PCS on 25G, 50G, and 100G links - Wangxun: - support Rx descriptor merge, and Tx head writeback - support Rx coalescing offload - support 25G SPF and 40G QSFP modules - Ethernet virtual: - Google (gve): - allow ethtool to configure rx_buf_len - implement XDP HW RX Timestamping support for DQ descriptor format - Microsoft vNIC (mana): - support HW link state events - handle hardware recovery events when probing the device - Ethernet NICs consumer, and embedded: - usbnet: add support for Byte Queue Limits (BQL) - AMD (amd-xgbe): - add device selftests - NXP (enetc): - add i.MX94 support - Broadcom integrated MACs (bcmgenet, bcmasp): - bcmasp: add support for PHY-based Wake-on-LAN - Broadcom switches (b53): - support port isolation - support BCM5389/97/98 and BCM63XX ARL formats - Lantiq/MaxLinear switches: - support bridge FDB entries on the CPU port - use regmap for register access - allow user to enable/disable learning - support Energy Efficient Ethernet - support configuring RMII clock delays - add tagging driver for MaxLinear GSW1xx switches - Synopsys (stmmac): - support using the HW clock in free running mode - add Eswin EIC7700 support - add Rockchip RK3506 support - add Altera Agilex5 support - Cadence (macb): - cleanup and consolidate descriptor and DMA address handling - add EyeQ5 support - TI: - icssg-prueth: support AF_XDP - Airoha access points: - add missing Ethernet stats and link state callback - add AN7583 support - support out-of-order Tx completion processing - Power over Ethernet: - pd692x0: preserve PSE configuration across reboots - add support for TPS23881B devices - Ethernet PHYs: - Open Alliance OATC14 10BASE-T1S PHY cable diagnostic support - Support 50G SerDes and 100G interfaces in Linux-managed PHYs - micrel: - support for non PTP SKUs of lan8814 - enable in-band auto-negotiation on lan8814 - realtek: - cable testing support on RTL8224 - interrupt support on RTL8221B - motorcomm: support for PHY LEDs on YT853 - microchip: support for LAN867X Rev.D0 PHYs w/ SQI and cable diag - mscc: support for PHY LED control - CAN drivers: - m_can: add support for optional reset and system wake up - remove can_change_mtu() obsoleted by core handling - mcp251xfd: support GPIO controller functionality - Bluetooth: - add initial support for PASTa - WiFi: - split ieee80211.h file, it's way too big - improvements in VHT radiotap reporting, S1G, Channel Switch Announcement handling, rate tracking in mesh networks - improve multi-radio monitor mode support, and add a cfg80211 debugfs interface for it - HT action frame handling on 6 GHz - initial chanctx work towards NAN - MU-MIMO sniffer improvements - WiFi drivers: - RealTek (rtw89): - support USB devices RTL8852AU and RTL8852CU - initial work for RTL8922DE - improved injection support - Intel: - iwlwifi: new sniffer API support - MediaTek (mt76): - WED support for >32-bit DMA - airoha NPU support - regdomain improvements - continued WiFi7/MLO work - Qualcomm/Atheros: - ath10k: factory test support - ath11k: TX power insertion support - ath12k: BSS color change support - ath12k: statistics improvements - brcmfmac: Acer A1 840 tablet quirk - rtl8xxxu: 40 MHz connection fixes/support" * tag 'net-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1381 commits) net: page_pool: sanitise allocation order net: page pool: xa init with destroy on pp init net/mlx5e: Support XDP target xmit with dummy program net/mlx5e: Update XDP features in switch channels selftests/tc-testing: Test CAKE scheduler when enqueue drops packets net/sched: sch_cake: Fix incorrect qlen reduction in cake_drop wireguard: netlink: generate netlink code wireguard: uapi: generate header with ynl-gen wireguard: uapi: move flag enums wireguard: uapi: move enum wg_cmd wireguard: netlink: add YNL specification selftests: drv-net: Fix tolerance calculation in devlink_rate_tc_bw.py selftests: drv-net: Fix and clarify TC bandwidth split in devlink_rate_tc_bw.py selftests: drv-net: Set shell=True for sysfs writes in devlink_rate_tc_bw.py selftests: drv-net: Use Iperf3Runner in devlink_rate_tc_bw.py selftests: drv-net: introduce Iperf3Runner for measurement use cases selftests: drv-net: Add devlink_rate_tc_bw.py to TEST_PROGS net: ps3_gelic_net: Use napi_alloc_skb() and napi_gro_receive() Documentation: net: dsa: mention simple HSR offload helpers Documentation: net: dsa: mention availability of RedBox ...
2025-12-03Merge tag 'printk-for-6.19' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux Pull printk updates from Petr Mladek: - Allow creaing nbcon console drivers with an unsafe write_atomic() callback that can only be called by the final nbcon_atomic_flush_unsafe(). Otherwise, the driver would rely on the kthread. It is going to be used as the-best-effort approach for an experimental nbcon netconsole driver, see https://lore.kernel.org/r/20251121-nbcon-v1-2-503d17b2b4af@debian.org Note that a safe .write_atomic() callback is supposed to work in NMI context. But some networking drivers are not safe even in IRQ context: https://lore.kernel.org/r/oc46gdpmmlly5o44obvmoatfqo5bhpgv7pabpvb6sjuqioymcg@gjsma3ghoz35 In an ideal world, all networking drivers would be fixed first and the atomic flush would be blocked only in NMI context. But it brings the question how reliable networking drivers are when the system is in a bad state. They might block flushing more reliable serial consoles which are more suitable for serious debugging anyway. - Allow to use the last 4 bytes of the printk ring buffer. - Prevent queuing IRQ work and block printk kthreads when consoles are suspended. Otherwise, they create non-necessary churn or even block the suspend. - Release console_lock() between each record in the kthread used for legacy consoles on RT. It might significantly speed up the boot. - Release nbcon context between each record in the atomic flush. It prevents stalls of the related printk kthread after it has lost the ownership in the middle of a record - Add support for NBCON consoles into KDB - Add %ptsP modifier for printing struct timespec64 and use it where possible - Misc code clean up * tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (48 commits) printk: Use console_is_usable on console_unblank arch: um: kmsg_dump: Use console_is_usable drivers: serial: kgdboc: Drop checks for CON_ENABLED and CON_BOOT lib/vsprintf: Unify FORMAT_STATE_NUM handlers printk: Avoid irq_work for printk_deferred() on suspend printk: Avoid scheduling irq_work on suspend printk: Allow printk_trigger_flush() to flush all types tracing: Switch to use %ptSp scsi: snic: Switch to use %ptSp scsi: fnic: Switch to use %ptSp s390/dasd: Switch to use %ptSp ptp: ocp: Switch to use %ptSp pps: Switch to use %ptSp PCI: epf-test: Switch to use %ptSp net: dsa: sja1105: Switch to use %ptSp mmc: mmc_test: Switch to use %ptSp media: av7110: Switch to use %ptSp ipmi: Switch to use %ptSp igb: Switch to use %ptSp e1000e: Switch to use %ptSp ...
2025-12-02Merge tag 'fpsimd-on-stack-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux Pull arm64 FPSIMD on-stack buffer updates from Eric Biggers: "This is a core arm64 change. However, I was asked to take this because most uses of kernel-mode FPSIMD are in crypto or CRC code. In v6.8, the size of task_struct on arm64 increased by 528 bytes due to the new 'kernel_fpsimd_state' field. This field was added to allow kernel-mode FPSIMD code to be preempted. Unfortunately, 528 bytes is kind of a lot for task_struct. This regression in the task_struct size was noticed and reported. Recover that space by making this state be allocated on the stack at the beginning of each kernel-mode FPSIMD section. To make it easier for all the users of kernel-mode FPSIMD to do that correctly, introduce and use a 'scoped_ksimd' abstraction" * tag 'fpsimd-on-stack-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (23 commits) lib/crypto: arm64: Move remaining algorithms to scoped ksimd API lib/crypto: arm/blake2b: Move to scoped ksimd API arm64/fpsimd: Allocate kernel mode FP/SIMD buffers on the stack arm64/fpu: Enforce task-context only for generic kernel mode FPU net/mlx5: Switch to more abstract scoped ksimd guard API on arm64 arm64/xorblocks: Switch to 'ksimd' scoped guard API crypto/arm64: sm4 - Switch to 'ksimd' scoped guard API crypto/arm64: sm3 - Switch to 'ksimd' scoped guard API crypto/arm64: sha3 - Switch to 'ksimd' scoped guard API crypto/arm64: polyval - Switch to 'ksimd' scoped guard API crypto/arm64: nhpoly1305 - Switch to 'ksimd' scoped guard API crypto/arm64: aes-gcm - Switch to 'ksimd' scoped guard API crypto/arm64: aes-blk - Switch to 'ksimd' scoped guard API crypto/arm64: aes-ccm - Switch to 'ksimd' scoped guard API raid6: Move to more abstract 'ksimd' guard API crypto: aegis128-neon - Move to more abstract 'ksimd' guard API crypto/arm64: sm4-ce-gcm - Avoid pointless yield of the NEON unit crypto/arm64: sm4-ce-ccm - Avoid pointless yield of the NEON unit crypto/arm64: aes-ce-ccm - Avoid pointless yield of the NEON unit lib/crc: Switch ARM and arm64 to 'ksimd' scoped guard API ...
2025-12-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Merge in late fixes in preparation for the net-next PR. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit (git 2.34.1) at 2026-01-06 01:42:31 +0000