| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git updates for v6.16-rc2
Fix a handful of both build and stability issues across multiple drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
ath11k_core_qmi_firmware_ready
if ath11k_crypto_mode is invalid (not ATH11K_CRYPT_MODE_SW/ATH11K_CRYPT_MODE_HW),
ath11k_core_qmi_firmware_ready() will not undo some actions that was previously
started/configured. Do the validation as soon as possible in order to avoid
undoing actions in that case and also to fix the following smatch warning:
drivers/net/wireless/ath/ath11k/core.c:2166 ath11k_core_qmi_firmware_ready()
warn: missing unwind goto?
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202304151955.oqAetVFd-lkp@intel.com/
Fixes: aa2092a9bab3 ("ath11k: add raw mode and software crypto support")
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250522200519.16858-1-rodrigo.gobbi.7@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently to get firmware stats, ath11k_mac_op_get_txpower() calls
ath11k_fw_stats_request() and ath11k_mac_op_sta_statistics() calls
ath11k_mac_get_fw_stats(). Those two helpers are basically doing
the same, except for:
1. ath11k_mac_get_fw_stats() verifies ar->state inside itself.
2. ath11k_mac_get_fw_stats() calls ath11k_mac_fw_stats_request()
which then calls ath11k_mac_fw_stats_reset() to free pdev/vdev
stats whereas only pdev stats are freed by ath11k_fw_stats_request().
3. ath11k_mac_get_fw_stats() waits for ar->fw_stats_complete and
ar->fw_stats_done, whereas ath11k_fw_stats_request() only waits for
ar->fw_stats_complete.
Change to call ath11k_mac_get_fw_stats() in ath11k_mac_op_get_txpower().
This is valid because:
1. ath11k_mac_op_get_txpower() also has the same request on ar->state.
2. it is harmless to call ath11k_fw_stats_vdevs_free() since
ar->fw_stats.vdevs should be empty and there should be no one
expecting it at that time.
3. ath11k_mac_op_get_txpower() only needs pdev stats. For pdev stats,
ar->fw_stats_done is set to true whenever ar->fw_stats_complete is
set to true in ath11k_update_stats_event(). So additional wait on
ar->fw_stats_done does not wast any time.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-8-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently ath11k_mac_get_fw_stats() is acquiring/releasing ar->conf_mutex by itself.
In order to reuse this function in a context where that lock is already taken, move
lock handling to its callers, then the function itself only has to assert it.
There is only one caller now, i.e., ath11k_mac_op_sta_statistics(), so add lock handling
there.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-7-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently RCU lock and ar->data_lock are acquired in a sequence of
rcu_read_lock()
spin_lock_bh(&ar->data_lock)
but released in a sequence of
rcu_read_unlock()
spin_unlock_bh(&ar->data_lock)
Although there are no apparent issues with this, reorder them to
achieve symmetry.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-6-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit b488c766442f ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855")
and commit c3b39553fc77 ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855")
call debugfs functions in mac ops. Those functions are no-ops if CONFIG_ATH11K_DEBUGFS is
not enabled, thus cause wrong status reported.
Move them to mac.c.
Besides, since WMI_REQUEST_RSSI_PER_CHAIN_STAT and WMI_REQUEST_VDEV_STAT stats could also
be requested via mac ops, process them directly in ath11k_update_stats_event().
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: b488c766442f ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855")
Fixes: c3b39553fc77 ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-5-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath11k_debugfs_fw_stats_process() we wait until all events received.
In case there is no vdev started, this results in that below condition
would never get satisfied
((++ar->fw_stats.num_vdev_recvd) == total_vdevs_started)
finally the requestor would be blocked until wait time out.
The same applies to WMI_REQUEST_BCN_STAT request as well due to:
((++ar->fw_stats.num_bcn_recvd) == ar->num_started_vdevs)
Change to check the number of started vdev first: if it is zero, finish
wait directly; if not, follow the old way.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-4-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently ath11k_debugfs_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever reason (
say ar->num_started_vdevs is 0 or firmware bug etc.) the following condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time when
firmware stats is requested again, even if everything is working fine, we will
fail due to the condition above will never be satisfied.
The same applies to num_bcn as well.
Change to use non-static counters so that we have a chance to clear them each
time firmware stats is requested. Currently only ath11k_fw_stats_request() and
ath11k_debugfs_fw_stats_request() are requesting firmware stats, so clear
counters there.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: da3a9d3c1576 ("ath11k: refactor debugfs code into debugfs.c")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-3-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
We get report [1] that CPU is running a hot loop in
ath11k_debugfs_fw_stats_request():
94.60% 0.00% i3status [kernel.kallsyms] [k] do_syscall_64
|
--94.60%--do_syscall_64
|
--94.55%--__sys_sendmsg
___sys_sendmsg
____sys_sendmsg
netlink_sendmsg
netlink_unicast
genl_rcv
netlink_rcv_skb
genl_rcv_msg
|
--94.55%--genl_family_rcv_msg_dumpit
__netlink_dump_start
netlink_dump
genl_dumpit
nl80211_dump_station
|
--94.55%--ieee80211_dump_station
sta_set_sinfo
|
--94.55%--ath11k_mac_op_sta_statistics
ath11k_debugfs_get_fw_stats
|
--94.55%--ath11k_debugfs_fw_stats_request
|
|--41.73%--_raw_spin_lock_bh
|
|--22.74%--__local_bh_enable_ip
|
|--9.22%--_raw_spin_unlock_bh
|
--6.66%--srso_alias_safe_ret
This is because, if for whatever reason ar->fw_stats_done is not set by
ath11k_update_stats_event(), ath11k_debugfs_fw_stats_request() won't yield
CPU before an up to 3s timeout.
Change to completion mechanism to avoid CPU burning.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yury Vostrikov <mon@unformed.ru>
Closes: https://lore.kernel.org/all/7324ac7a-8b7a-42a5-aa19-de52138ff638@app.fastmail.com/ # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-2-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
|
|
The PCI_PWRCTRL_PWRSEQ and HAVE_PWRCTRL symbols have been renamed to
reflect the pwrctrl framework name. Switch to the non-deprecated symbols.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org> # drivers/net/wireless/ath/...
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250402132634.18065-3-johan+linaro@kernel.org
|
|
Now some chips which support 'support_dual_stations' will enable DBS,
but will disable DFS. Restructure the ath11k_mac_setup_iface_combinations
function to support DBS and DFS compatibility.
About 'support_dual_station' feature can refer:
https://msgid.link/20230714023801.2621802-2-quic_cjhuang@quicinc.com
Add a ieee80211_iface_combination to support DBS and DFS compatibility,
one combination can support DFS(same with non dual sta), another
combination can support DBS. When running different scenarios that will
use different ieee80211_iface_combination due to mac80211 will go through
all of possible interface combinations.
In addition, maximum number of interfaces of these types should be total
allowed in this group.
The chips affected are:
QCA6390 hw2.0
WCN6855 hw2.0
WCN6855 hw2.1
Other chips are not affected.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-00410-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04402-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Link: https://patch.msgid.link/20241127022742.4016870-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barrier to make sure that the REO dest ring
descriptor is read after the head pointer to avoid using stale data on
weakly ordered architectures like aarch64.
This may fix the ring-buffer corruption worked around by commit
f9fff67d2d7c ("wifi: ath11k: Fix SKB corruption in REO destination
ring") by silently discarding data, and may possibly also address user
reported errors like:
ath11k_pci 0006:01:00.0: msdu_done bit in attention is not set
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218005
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Link: https://patch.msgid.link/20250321145302.4775-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Users of the Lenovo ThinkPad X13s have reported that Wi-Fi sometimes
breaks and the log fills up with errors like:
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1484, expected 1492
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1460, expected 1484
which based on a quick look at the driver seemed to indicate some kind
of ring-buffer corruption.
Miaoqing Pan tracked it down to the host seeing the updated destination
ring head pointer before the updated descriptor, and the error handling
for that in turn leaves the ring buffer in an inconsistent state.
Add the missing memory barrier to make sure that the descriptor is read
after the head pointer to address the root cause of the corruption while
fixing up the error handling in case there are ever any (ordering) bugs
on the device side.
Note that the READ_ONCE() are only needed to avoid compiler mischief in
case the ring-buffer helpers are ever inlined.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218623
Link: https://lore.kernel.org/20250310010217.3845141-3-quic_miaoqing@quicinc.com
Cc: Miaoqing Pan <quic_miaoqing@quicinc.com>
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Link: https://patch.msgid.link/20250321094916.19098-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Firmware requests 2 segments at first. The first segment is of 6799360
whose allocation fails due to dma remapping not available. The success
is returned to firmware. Then firmware asks for 22 smaller segments
instead of 2 big ones. Those get allocated successfully. At suspend/
hibernation time, these segments aren't freed as they will be reused
by firmware after resuming.
After resuming, the firmware asks for the 2 segments again with the
first segment of 6799360 size. Since chunk->vaddr is not NULL, the
type and size are compared with the previous type and size to know if
it can be reused or not. Unfortunately, it is detected that it cannot
be reused and this first smaller segment is freed. Then we continue to
allocate 6799360 size memory which fails and ath11k_qmi_free_target_mem_chunk()
is called which frees the second smaller segment as well. Later success
is returned to firmware which asks for 22 smaller segments again. But
as we had freed 2 segments already, we'll allocate the first 2 new
smaller segments again and reuse the remaining 20. Hence 20 small
segments are being reused instead of 22.
Add skip logic when vaddr is set, but size/type don't match. Use the
same skip and success logic as used when dma_alloc_coherent() fails.
By skipping, the possibility of resume failure due to kernel failing to
allocate memory for QMI can be avoided.
kernel: ath11k_pci 0000:03:00.0: failed to allocate dma memory for qmi (524288 B type 1)
ath11k_pci 0000:03:00.0: failed to allocate qmi target memory: -22
Tested-on: WCN6855 WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.6
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250428080242.466901-1-usama.anjum@collabora.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath into wireless-next
Jeff Johnson says:
====================
ath.git patches for v6.16
ath12k:
Enable AHB support for IPQ5332.
Add monitor interface support to QCN9274.
Add MLO support to WCN7850.
Add 802.11d scan offload support to WCN7850.
ath11k:
Restore hibernation support
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
====================
Change-Id: I6555e64d7434f3a5fed5faab25057be93106b18e
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For MBSSID, each vif (struct ieee80211_vif) stores another vif
pointer for the transmitting profile of MBSSID set. This won't
suffice for MLO as there may be multiple links, each of which can
be part of different MBSSID sets. Hence the information needs to
be stored per-link. Additionally, the transmitted profile itself
may be part of an MLD hence storing vif will not suffice either.
Fix MLO by storing an instance of struct ieee80211_bss_conf
for each link.
Modify following operations to reflect the above structure updates:
- channel switch completion
- BSS color change completion
- Removing nontransmitted links in ieee80211_stop_mbssid()
- drivers retrieving the transmitted link for beacon templates.
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Co-developed-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408184501.3715887-3-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-2-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The use of of_property_read_u32() isn't really correct as
"memory-region" contains phandles (though those happen to be u32s. As
it is just testing for property presence, use of_property_present()
instead.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250408190211.2505737-2-robh@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In current WLAN recovery code flow, ath11k_core_halt() only
reinitializes the "arvifs" list head. This will cause the
list node immediately following the list head to become an
invalid list node. Because the prev of that node still points
to the list head "arvifs", but the next of the list head "arvifs"
no longer points to that list node.
When a WLAN recovery occurs during the execution of a vif
removal, and it happens before the spin_lock_bh(&ar->data_lock)
in ath11k_mac_op_remove_interface(), list_del() will detect the
previously mentioned situation, thereby triggering a kernel panic.
The fix is to remove and reinitialize all vif list nodes from the
list head "arvifs" during WLAN halt. The reinitialization is to make
the list nodes valid, ensuring that the list_del() in
ath11k_mac_op_remove_interface() can execute normally.
Call trace:
__list_del_entry_valid_or_report+0xb8/0xd0
ath11k_mac_op_remove_interface+0xb0/0x27c [ath11k]
drv_remove_interface+0x48/0x194 [mac80211]
ieee80211_do_stop+0x6e0/0x844 [mac80211]
ieee80211_stop+0x44/0x17c [mac80211]
__dev_close_many+0xac/0x150
__dev_change_flags+0x194/0x234
dev_change_flags+0x24/0x6c
devinet_ioctl+0x3a0/0x670
inet_ioctl+0x200/0x248
sock_do_ioctl+0x60/0x118
sock_ioctl+0x274/0x35c
__arm64_sys_ioctl+0xac/0xf0
invoke_syscall+0x48/0x114
...
Tested-on: QCA6698AQ hw2.1 PCI WLAN.HSP.1.1-04591-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Stone Zhang <quic_stonez@quicinc.com>
Link: https://patch.msgid.link/20250320053145.3445187-1-quic_stonez@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
This reverts commit d3e154d7776ba57ab679fb816fb87b627fba21c9.
With non-WoWLAN suspend support brought back, commit 7f0343b7b871 ("wifi:
ath11k: restore country code during resume") needs to be brought back
as well.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-6-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Now WoWLAN mode is chosen for those machines listed in the quirk table.
This works for suspend (S3) but breaks for hibernation (S4), because
WoWLAN mode requires WLAN power to be sustained, which is not the case
during hibernation. For hibernation, the default mode should be used.
Register a PM notifier with which kernel can notify us of the actual PM
operation: if system is going to suspend, the original PM policy is
honored; while if it is hibernation, overwrite it with default policy.
To summarize: for suspend (S3), WoWLAN mode is chosen for machines listed
in the quirk table, non-WoWLAN mode for others; for hibernation (S4),
non-WoWLAN mode is chosen for all.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-5-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Previously commit 166a490f59ac ("wifi: ath11k: support hibernation") was
reverted due to [1], so currently we only support WoWLAN mode suspend.
This works well in scenarios where WLAN power is sustained during suspend,
however breaks in those where power is cut off.
This change basically brings the reverted commit back, but differs in that
we decide based on the PM policy to choose WoWLAN mode suspend or the
non-WoWLAN mode. As stated in the previous patch for now the PM policy is
determined based on machine models. That said we will choose WoWLAN mode
suspend if we are running on machines listed in ath11k_pm_quirk_table,
otherwise we choose the other one.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-4-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Due to [1] we currently put WLAN target into WoWLAN mode regardless of
machine models. In upcoming patches we will support another mode, and
finally which mode is chosen depends on the exact machine model.
To prepare for such change, refactor the actual WoWLAN stuff in
ath11k_core_suspend() into a new helper ath11k_core_suspend_wow(), this
increase the code readability when the new suspend mode is added in
upcoming patches.
Same change applies to ath11k_core_resume();
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-3-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently ath11k_core_suspend() and ath11k_core_resume() have the same
check before going on. In upcoming patches the check is needed by some
newly added functions as well.
To avoid duplicate code, introduce a new helper
ath11k_core_continue_suspend_resume() which does such check internally.
Callers can decide whether to go on based on its return value.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-2-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
To handle the Lenovo unexpected wakeup issue [1], previously we revert
commit 166a490f59ac ("wifi: ath11k: support hibernation"). So currently
WLAN target is put into WoWLAN mode during suspend. This is a temporary
solution as it does not work on machines where WLAN power is cut off.
The thought here is that we do WoWLAN suspend on Lenovo machines while
do non-WoWLAN suspend (which is done in the reverted commit) on other
machines. This requires us to identify Lenovo machines from others.
For that purpose, read board vendor and product name from DMI interface,
match it against all known affected machines. If there is a match, choose
WoWLAN suspend mode, else choose non-WoWLAN mode. Save the mode in ab
for later reference.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-1-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
====================
ath.git patches for v6.15
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
====================
Link: https://lore.kernel.org/linux-wireless/d01b1976-ebe8-48cd-8f49-32bfa00bed7e@oss.qualcomm.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for calibration-like properties without 'ath11k' prefix,
while still keeping everything backwards compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250225-b-wifi-qcom-calibration-variant-v1-5-3b2aa3f89c53@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Function ath11k_mac_setup_bcn_tmpl() retrieves tx_arvif only for
a sanity check and then calls ath11k_mac_setup_bcn_tmpl_mbssid()
or ath11k_mac_setup_bcn_tmpl_ema() both of which again retrieve
the same pointer. Instead store the pointer and pass it to the
latter two functions. Compile tested only.
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-3-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Create a new function ath11k_mac_get_tx_arvif() to retrieve 'arvif'
for the transmitted interface of the MBSSID set. This will help
modifying the same code path to reflect mac80211 data structure
changes to support MLO. This also fixes an issue in
ath11k_mac_update_vif_chan() where tx_arvif is not reset to NULL
inside for loop during each iteration. Compile tested only.
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-2-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
irq_set_affinity_and_hint()
irq_set_affinity_hint() API is deprecated now, so let's use the recommended
equivalent irq_set_affinity_and_hint().
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250225053447.16824-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
error path
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath11k_pci_alloc_msi(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ. This results in the
below warning:
WARNING: CPU: 7 PID: 349 at kernel/irq/manage.c:1929 free_irq+0x278/0x29c
Call trace:
free_irq+0x278/0x29c
ath11k_pcic_free_irq+0x70/0x10c [ath11k]
ath11k_pci_probe+0x800/0x820 [ath11k_pci]
local_pci_probe+0x40/0xbc
The warning is due to not clearing the affinity hint before freeing the
IRQs.
So to fix this issue, clear the IRQ affinity hint before calling
ath11k_pcic_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Cc: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 39564b475ac5 ("wifi: ath11k: fix boot failure with one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In case of firmware assert snapshot of firmware memory is essential for
debugging. Add firmware coredump collection support for PCI bus.
Collect RDDM and firmware paging dumps from MHI and pack them in TLV
format and also pack various memory shared during QMI phase in separate
TLVs. Add necessary header and share the dumps to user space using dev
coredump framework. Coredump collection is controlled by
CONFIG_DEV_COREDUMP. Dump collected for a radio is 55 MB approximately.
The changeset is mostly copied from:
https://lore.kernel.org/all/20240325183414.4016663-1-quic_ssreeela@quicinc.com/.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04358-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240813013028.2708111-2-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The value of 'ab->hw_params.fixed_mem_region' determines that
only one variable 'vaddr' or 'iaddr' is used in target_mem_chunk.
So use an anonymous union instead, easy to check whether the
memory is set or not.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04358-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240813013028.2708111-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath11k_hal_srng_* should be used with srng->lock to protect srng data.
For ath11k_dp_rx_mon_dest_process() and ath11k_dp_full_mon_process_rx(),
they use ath11k_hal_srng_* for many times but never call srng->lock.
So when running (full) monitor mode, warning will occur:
RIP: 0010:ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
Call Trace:
? ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
ath11k_dp_rx_process_mon_status+0xc45/0x1190 [ath11k]
? idr_alloc_u32+0x97/0xd0
ath11k_dp_rx_process_mon_rings+0x32a/0x550 [ath11k]
ath11k_dp_service_srng+0x289/0x5a0 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xd0 [ath11k]
__napi_poll+0x30/0x1f0
net_rx_action+0x198/0x320
__do_softirq+0xdd/0x319
So add srng->lock for them to avoid such warnings.
Inorder to fetch the srng->lock, should change srng's definition from
'void' to 'struct hal_srng'. And initialize them elsewhere to prevent
one line of code from being too long. This is consistent with other ring
process functions, such as ath11k_dp_process_rx().
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241219110531.2096-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
While processing the monitor destination ring, MSDUs are reaped from the
link descriptor based on the corresponding buf_id.
However, sometimes the driver cannot obtain a valid buffer corresponding
to the buf_id received from the hardware. This causes an infinite loop
in the destination processing, resulting in a kernel crash.
kernel log:
ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309
ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed
ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309
ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed
Fix this by skipping the problematic buf_id and reaping the next entry,
replacing the break with the next MSDU processing.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241219110531.2096-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
With previous patch "wifi: ath11k: move update channel list from update
reg worker to reg notifier", ath11k_reg_update_chan_list() will be
called during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath11k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called and will not increase the occupation time of rtnl_lock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Co-developed-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently when ath11k gets a new channel list, it will be processed
according to the following steps:
1. update new channel list to cfg80211 and queue reg_work.
2. cfg80211 handles new channel list during reg_work.
3. update cfg80211's handled channel list to firmware by
ath11k_reg_update_chan_list().
But ath11k will immediately execute step 3 after reg_work is just
queued. Since step 2 is asynchronous, cfg80211 may not have completed
handling the new channel list, which may leading to an out-of-bounds
write error:
BUG: KASAN: slab-out-of-bounds in ath11k_reg_update_chan_list
Call Trace:
ath11k_reg_update_chan_list+0xbfe/0xfe0 [ath11k]
kfree+0x109/0x3a0
ath11k_regd_update+0x1cf/0x350 [ath11k]
ath11k_regd_update_work+0x14/0x20 [ath11k]
process_one_work+0xe35/0x14c0
Should ensure step 2 is completely done before executing step 3. Thus
Wen raised patch[1]. When flag NL80211_REGDOM_SET_BY_DRIVER is set,
cfg80211 will notify ath11k after step 2 is done.
So enable the flag NL80211_REGDOM_SET_BY_DRIVER then cfg80211 will
notify ath11k after step 2 is done. At this time, there will be no
KASAN bug during the execution of the step 3.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/20230201065313.27203-1-quic_wgong@quicinc.com/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: f45cb6b29cd3 ("wifi: ath11k: avoid deadlock during regulatory update in ath11k_regd_update()")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Current code in ath11k_mac_set_txbf_conf overrides nsts, which is
incorrect as it confuses nss and nsts. nss is Number of Spatial
Streams，nsts is Number of Space-Time Streams.
As mentioned in Fixes: 55b5ee3357d7, the nss used when acting as a
beamformee in VHT mode should be reported by the firmware and should not
be greater than the number of receiving antennas - 1. The num_rx_chains
related nss rather than nsts.
If STBC is enabled, nsts is greater than nss. About nss are mapped to
nsts, refer to IEEE Std 802.11-2020: 19.3.11.9.2 Space-time block coding
(STBC), Table 19-18—Constellation mapper output to spatial mapper input
for STBC.
Remove wrong overriding for nsts of VHT Beamformee STS Capability,
acting DL MU-MIMO in VHT mode is working properly.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Fixes: 55b5ee3357d7 ("wifi: ath11k: fix number of VHT beamformee spatial streams")
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124075953.2282354-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The current code does not have the MU EDCA feature, so it cannot support
the use of EDCA by STA in specific UL MU HE TB PPDU transmissions. Refer
to IEEE Std 802.11ax-2021 "9.4.2.251 MU EDCA Parameter Set element",
"26.2.7 EDCA operation using MU EDCA parameters".
Add ath11k_mac_op_conf_tx_mu_edca() to construct the MU EDCA parameters
received from mac80211 into WMI WMM parameters，and send to the firmware
according to the different WMM type flags.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04523-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124061343.2263467-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit b205ce4c266c ("ath11k: support avg signal in station dump") added an
extra assignment of arsta->rssi_comb in ath11k_dp_rx_update_peer_stats()
when it added the average rssi support. So let's keep only one by removing
the legacy assignment so the two statements about rssi stay next to each
other. Compile tested only.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://patch.msgid.link/20250117181953.3375273-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Mainly individually changelogged singleton patches. The patch series
in this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap
library code
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms
some cleanup and Rust preparation in the xarray library code
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven
fixes pathnames in some code comments
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses
the new secs_to_jiffies() in various places where that is
appropriate
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API
- "Convert ocfs2 to use folios" from Matthew Wilcox does that
- "Remove get_task_comm() and print task comm directly" from Yafang
Shao removes now-unneeded calls to get_task_comm() in various
places
- "squashfs: reduce memory usage and update docs" from Phillip
Lougher implements some memory savings in squashfs and performs
some maintainability work
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented
with a corrupted image
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger
- "minmax.h: Cleanups and minor optimisations" from David Laight does
some maintenance work on the min/max library code
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance
work on the xarray library code"
* tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (131 commits)
ocfs2: use str_yes_no() and str_no_yes() helper functions
include/linux/lz4.h: add some missing macros
Xarray: use xa_mark_t in xas_squash_marks() to keep code consistent
Xarray: remove repeat check in xas_squash_marks()
Xarray: distinguish large entries correctly in xas_split_alloc()
Xarray: move forward index correctly in xas_pause()
Xarray: do not return sibling entries from xas_find_marked()
ipc/util.c: complete the kernel-doc function descriptions
gcov: clang: use correct function param names
latencytop: use correct kernel-doc format for func params
minmax.h: remove some #defines that are only expanded once
minmax.h: simplify the variants of clamp()
minmax.h: move all the clamp() definitions after the min/max() ones
minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()
minmax.h: reduce the #define expansion of min(), max() and clamp()
minmax.h: update some comments
minmax.h: add whitespace around operators and after commas
nilfs2: do not update mtime of renamed directory that is not moved
nilfs2: handle errors that nilfs_prepare_chunk() may return
CREDITS: fix spelling mistake
...
|
|
The firmware memory was allocated in ath11k_pci_probe() or
ath11k_ahb_probe(), but not freed in ath11k_xxx_remove() in case
ATH11K_FLAG_QMI_FAIL bit is set. So call ath11k_fw_destroy() to
free the memory.
Found while fixing the same problem in ath12k:
https://lore.kernel.org/linux-wireless/20240314012746.2729101-1-quic_miaoqing@quicinc.com
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04546-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250123084948.1124357-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
User space application requires that the testmode interface
is exactly same between ath drivers. Move testmode_i.h file
in ath directory to ensure that all ath driver uses same testmode
interface instead of duplicating testmode_i.h for each ath drivers.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-2-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the driver allocates cacheable DMA buffers for the rx_tid
structure using kzalloc() and dma_map_single(). These buffers are
long-lived and can persist for the lifetime of the peer, which is not
advisable. Instead of using kzalloc() and dma_map_single() for allocating
cacheable DMA buffers, utilize the dma_alloc_noncoherent() helper for the
allocation of long-lived cacheable DMA buffers, such as the peer's rx_tid.
Since dma_alloc_noncoherent() returns unaligned physical and virtual
addresses, align them internally before use within the driver. This
ensures proper allocation of non-coherent memory through the kernel
helper.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Link: https://patch.msgid.link/20250119164219.647059-3-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the driver allocates cacheable DMA buffers for rings like
HAL_REO_DST and HAL_WBM2SW_RELEASE. The buffers for HAL_WBM2SW_RELEASE
are large (1024 KiB), exceeding the SWIOTLB slot size of 256 KiB. This
leads to "swiotlb buffer is full" error messages on systems without an
IOMMU that use SWIOTLB, causing driver initialization failures. The driver
calls dma_map_single() with these large buffers obtained from kzalloc(),
resulting in ring initialization errors on systems without an IOMMU that
use SWIOTLB.
To address these issues, replace the flawed buffer allocation mechanism
with the appropriate DMA API. Specifically, use dma_alloc_noncoherent()
for cacheable DMA buffers, ensuring proper freeing of buffers with
dma_free_noncoherent().
Error log:
[ 10.194343] ath11k_pci 0000:04:00.0: swiotlb buffer is full (sz:1048583 bytes), total 32768 (slots), used 2529 (slots)
[ 10.194406] ath11k_pci 0000:04:00.0: failed to set up tcl_comp ring (0) :-12
[ 10.194781] ath11k_pci 0000:04:00.0: failed to init DP: -12
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Reported-by: Tim Harvey <tharvey@gateworks.com>
Closes: https://lore.kernel.org/all/20241210041133.GA17116@lst.de/
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Link: https://patch.msgid.link/20250119164219.647059-2-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit b35108a51cf7 ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
@@ constant C; @@
- msecs_to_jiffies(C * 1000)
+ secs_to_jiffies(C)
@@ constant C; @@
- msecs_to_jiffies(C * MSEC_PER_SEC)
+ secs_to_jiffies(C)
Link: https://lkml.kernel.org/r/20241210-converge-secs-to-jiffies-v3-14-ddfefd7e9f2a@linux.microsoft.com
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Anna-Maria Behnsen <anna-maria@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Daniel Mack <daniel@zonque.org>
Cc: David Airlie <airlied@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Jeff Johnson <jjohnson@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Julia Lawall <julia.lawall@inria.fr>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nicolas Palix <nicolas.palix@imag.fr>
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Praveen Kaligineedi <pkaligineedi@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Shailend Chand <shailend@google.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Simon Horman <horms@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
